06-16-2016, 07:29 PM | #1 |
Lieutenant Colonel
882
Rep 1,661
Posts |
Courtesy access seat coding
Had my car coded last night by Okee at Codemycar.com. Always great.
I sent him the the courtesy access drivers seat and front fog light coding that I found on this thread, but neither is working. Any ideas?
__________________
18' F80 6MT, 991.1s cab PDK, F83 6mt, 996 C4S cab 6mt, F30 328iM 6mt
E60 M5 SMG, E39 M5, E46 M3 cab 6mt, E36 M3 5mt |
06-16-2016, 11:09 PM | #2 |
Captain
376
Rep 600
Posts |
Hi,
Two modules are involved. FEM_BODY: 30C0 EINSTIEGSH_LN_AKTIV = aktiv 30C0 EINSTIEGSH_NG_AKTIV = aktiv 30C0 PRIO_ACHSEN = set to 1 or 2 (not sure what these values do but mine is set to 1) SM (There are 2 ECUs named SMx on my car. One is for driver seat the other one is for passenger. I use the first one on the list in E-Sys) 3000 EINAUSSTIEGSHILFE = Modus_FA_SLV 3012 EAH_VERFAHRWEG_SLV_PHYS = 00, 28 3012 EAH_SCHUTZFREIRAUM_HINTEN_SLV_PHYS = 00, 3C |
Appreciate
1
audioMeth222.00 |
06-17-2016, 08:44 AM | #3 |
New Member
13
Rep 20
Posts |
What is courtesy seat coding supposed to do?
For the fog light coding did you follow the DIY to make the switches work? The rear fog lights are fairly straight forward. My front fog lights didn't work until after I had coded NGHB. I don't think they work unless you have VLD activated which happens when you go through the process for NGHB. |
Appreciate
0
|
06-17-2016, 10:27 AM | #4 |
Captain
376
Rep 600
Posts |
Courtesy access driver seat basically moves back the driver seat when you open the door to give you more room to sit.
When you open the door after the ignition is off, the seat will move to give you more room to get out. Apart from being convenient for me, it helps protect the leather on the seat a little more. |
Appreciate
1
WestBankM4248.00 |
06-17-2016, 10:30 AM | #5 | |
Banned
3216
Rep 2,385
Posts |
Quote:
|
|
Appreciate
0
|
06-17-2016, 10:46 AM | #6 | |
Brigadier General
3460
Rep 3,995
Posts |
Quote:
My wife's Infiniti does the seat moving thing. I always end up getting in fine, then it jams me up against the dash when I start the car since she's about 6 inches shorter than me. Personally, I don't want anything to move...ever.
__________________
Current: G82 M4 Comp xDrive // Frozen Deep Grey
Current: 95B.1 Macan Turbo // Dark Blue Metallic |
|
Appreciate
0
|
06-17-2016, 10:52 AM | #7 |
Captain
376
Rep 600
Posts |
|
Appreciate
0
|
06-17-2016, 10:56 AM | #8 | |
Captain
376
Rep 600
Posts |
Quote:
With this feature enabled I sometimes feel like the man in the picture below |
|
Appreciate
1
|
06-17-2016, 11:20 AM | #9 | |
Lieutenant
175
Rep 500
Posts |
Quote:
|
|
Appreciate
1
|
06-17-2016, 02:03 PM | #10 |
Lieutenant Colonel
882
Rep 1,661
Posts |
"For the fog light coding did you follow the DIY to make the switches work? The rear fog lights are fairly straight forward. My front fog lights didn't work until after I had coded NGHB. I don't think they work unless you have VLD activated which happens when you go through the process for NGHB"
I did do the DIY switch mod. Drove the car in the dark and it turns out that the coding did work. The anti dazzle LED coding was amazing. Totally changed my opinion of the LED's.
__________________
18' F80 6MT, 991.1s cab PDK, F83 6mt, 996 C4S cab 6mt, F30 328iM 6mt
E60 M5 SMG, E39 M5, E46 M3 cab 6mt, E36 M3 5mt |
Appreciate
0
|
06-17-2016, 02:48 PM | #12 |
Lieutenant Colonel
882
Rep 1,661
Posts |
I was really surprised how much activity and adjusting the lights were doing. Constantly moving. Cool.
BTW - my main reason for the courtesy seating is to spare the seat bolster some. I've got less than 2k miles and it's already starting to wrinkle.
__________________
18' F80 6MT, 991.1s cab PDK, F83 6mt, 996 C4S cab 6mt, F30 328iM 6mt
E60 M5 SMG, E39 M5, E46 M3 cab 6mt, E36 M3 5mt |
Appreciate
0
|
06-18-2016, 10:46 AM | #13 |
Private First Class
106
Rep 191
Posts |
For what it's worth, I only coded one single line in SM(6d) to get this working.
3000 EINAUSSTIEGSHILFE = Modus_FA_SLV This may work for others as well. |
Appreciate
0
|
06-23-2016, 06:13 AM | #14 |
Lieutenant Colonel
882
Rep 1,661
Posts |
Had this coded, but it doesn't work consistently. If I reset my memory presets it seems to work and stops soon after.
__________________
18' F80 6MT, 991.1s cab PDK, F83 6mt, 996 C4S cab 6mt, F30 328iM 6mt
E60 M5 SMG, E39 M5, E46 M3 cab 6mt, E36 M3 5mt |
Appreciate
0
|
09-04-2016, 04:16 PM | #16 | |
Lieutenant Colonel
882
Rep 1,661
Posts |
Quote:
__________________
18' F80 6MT, 991.1s cab PDK, F83 6mt, 996 C4S cab 6mt, F30 328iM 6mt
E60 M5 SMG, E39 M5, E46 M3 cab 6mt, E36 M3 5mt |
|
Appreciate
0
|
09-05-2016, 08:59 PM | #17 |
Lieutenant General
2146
Rep 10,176
Posts |
None, coded it as instructed above. You do need to start the car between it moving forward and back again...
So, if you are showing the feature off, open door, get in car and close door (seat moves forward). If you open the door again, it will not move back. However, if you start the car after the seat moves forward (like you would in a normal driving cycle), shut the car off and then open the door, the seat will move back for you. |
Appreciate
0
|
09-05-2016, 09:25 PM | #18 |
General
21115
Rep 20,741
Posts
Drives: 2021 911 turbo
Join Date: Jan 2012
Location: Montreal
|
I love this feature at the track. I install myself in the driver's seat with the door open, put my helmet on, put on the safety belt, tighten the belt around my waist, sharply pull on the shoulder strap to get the belt to lock and then close the door. The seat moves forward with the belt locked and I am firmly strapped into position .
__________________
Porsche 911 turbo 2021 992 GT Silver
Previous cars: M4cs 2019 F82 Limerock Grey / M4 2015 F82 Silverstone / M3 2008 E92 Silverstone / M3 2002 E46 Carbon Black |
Appreciate
1
stealth70mde375.50 |
09-13-2016, 11:04 PM | #20 |
Lieutenant General
2146
Rep 10,176
Posts |
Yes. I have it coded on mine, and coded it on other M4s. There is a thread on controlling the distance of travel, and I used to increase travel on my friend's car on Sunday, who's a bit shorter than I am. I changed the 00,28 value to 00,50, for 8cm of travel compared to 4cm, which is what 00,28 affords.
So, those who want to vary the amount of travel, here's some setting options that work (in addition to the above coding): 3012 EAH_VERFAHRWEG_SLV_PHYS = 00, 28 (for 4cm travel) 3012 EAH_VERFAHRWEG_SLV_PHYS = 00, 3C (for 6cm travel) 3012 EAH_VERFAHRWEG_SLV_PHYS = 00, 50 (for 8cm travel) 3012 EAH_VERFAHRWEG_SLV_PHYS = 00, 64 (for 10cm of travel) Keep in mind that it will stop at the distance back, if 10cm is further than the travel allows. |
Appreciate
1
CanAutM321115.00 |
11-17-2016, 08:30 AM | #21 |
First Lieutenant
88
Rep 340
Posts |
Is yours working yet? I'm in the same situation as you. It worked for a very short period of time, then now it doesn't work at all. I wonder what caused it to reset itself. It's been driving me nuts
|
Appreciate
0
|
11-17-2016, 09:12 AM | #22 |
Major
868
Rep 1,413
Posts
Drives: 2020 X3MC
Join Date: Jan 2016
Location: Sykesville, MD
|
I tried to code this in mine as well and can't get it to work at all. It's the only item that I can't get to work and its driving me nuts!!
Anyone that has any pointers to make this work would be greatly appreciated. |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|