11-21-2017, 10:33 AM | #1 |
Rocket Man
20
Rep 129
Posts |
2018 Adaptive LED + Anti-Dazzle Issue
2018 M4 - got the car coded and turned up the brightness of the lights, anti-dazzle and adaptive thing as well.
Now at night it seems like it's just the brights are on (even without them turned on). The beam shaping thing does not work (but I can see the bright signal on the dash going on and off when cars are coming). It just seems the brights are always on, I get flashed at night non stop. When I turn my brights on manually at night I see no difference between the normal lights and brights, nothing changes. I was one of the first, if not the first, 2018 M4 with adaptive LEDs coded at the place I went to. Anyone else run into this or what could be the issue? Getting flashed constantly at night is annoying and I think I'm blinding people. Is there any way to re-set this without coding since the place I went to is 2 hours away... Thanks. |
11-21-2017, 10:54 AM | #2 |
Major
516
Rep 1,247
Posts
Drives: 2022 Taycan GTS, 2018 M4, 2016
Join Date: May 2009
Location: Rowland Heights, CA
|
2018 headlight coding is a little bit different. When I did my car coding in EAS, Tom saw the difference and took few hrs to make it work. The high beam(bottom light) was always on. You might have same problem.
|
Appreciate
0
|
11-21-2017, 02:38 PM | #3 |
Major General
2374
Rep 8,364
Posts |
No way to set without recoding, but it can be done remotely rather than drive 2 hours. Also, if you have copy of your coded files, I can take a look to see if done correctly.
|
Appreciate
0
|
11-21-2017, 02:54 PM | #4 |
Banned
7561
Rep 5,056
Posts |
So did It work properly and then just suddenly stopped working? I'm thinking of getting my '18 coded but hesitant because coders might not be familiar the '18 yet.
|
Appreciate
0
|
11-21-2017, 05:01 PM | #5 |
Rocket Man
20
Rep 129
Posts |
No - it's always been like the brights are always on. I've just been gone a ton and barely had time to drive it since coding about 5-6 mos ago.
|
Appreciate
0
|
11-21-2017, 05:02 PM | #6 |
Rocket Man
20
Rep 129
Posts |
How do you remote code? Do you need a special device or anything? I don't have the code files...
|
Appreciate
0
|
11-21-2017, 05:08 PM | #7 | |
Major General
2374
Rep 8,364
Posts |
Quote:
It works if done correctly, but not if only VO coded or using incorrect chassis settings. |
|
Appreciate
0
|
04-26-2018, 09:24 AM | #8 |
Lieutenant Colonel
928
Rep 1,496
Posts |
Has anyone found a solution in being able to activate properly functioning Anti-Dazzle in 2018 icon adaptive LEDs?
__________________
| M-Performance Exhaust | JB4 Map 4 on E35 | BMC Red Panel Filter |
| Previous: 18 M3 ZCP | 17 M3 6MT | 15 M235i | |
Appreciate
0
|
04-26-2018, 01:32 PM | #9 | |
The G8X is a disaster. 🤮
931
Rep 988
Posts |
Quote:
I tried for a bit to get mine working, but the right headlight continued to dazzle oncoming traffic. Otherwise they worked semi-OK. I coded back to US spec. |
|
Appreciate
1
PhatLyfe985.00 |
04-27-2018, 10:32 AM | #10 | |
Zymurgist
89
Rep 161
Posts |
Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|