Coding out: 3 little Amber LED's in the headlights?

[aboulfad]

Originally Posted by absoluteis350

Out of curiosity, why isn't part of the "Codes that worked for me" sticky since it seems to be often requested, but buried deep within this forum ?

You can ask the owner of that OP to update the sticky. I and many others probably made requests to sticky those so if you ask maybe it'll be done.

[Deja_Vu]

Originally Posted by dmnc02

This should do it for LEDs (but I haven't confirmed this on my car since they don't bother me):

Both TMS modules, FDL Code Standlicht Modus 1 & Standlicht Modus 2, change the Werte Value 64 to 00 as follows:
00, 03, 00, 00, 64, 03, 00, 00, 64, 03, 00, 00, 2B, 04, 00, 00
00, 03, 00, 00, 00, 03, 00, 00, 64, 03, 00, 00, 2B, 04, 00, 00

http://www.bimmerfest.com/forums/sho....php?p=9125089

Sorry for the bump, but these did not work for me. I've coded NGHB, removed the dongs, easy access seats and a number of other things but for some reason this is not working. When attempting to code the FDL the values aren't writing. Pre-code values in the FDL are saved correctly, but after coding (with no errors reported) and then reading the the coding data again, the FDL has reverted back. Any ideas as to why?

Pre-coding:

[dmnc02]

Originally Posted by Deja_Vu

Sorry for the bump, but these did not work for me. I've coded NGHB, removed the dongs, easy access seats and a number of other things but for some reason this is not working. When attempting to code the FDL the values aren't writing. Pre-code values in the FDL are saved correctly, but after coding (with no errors reported) and then reading the the coding data again, the FDL has reverted back. Any ideas as to why?

Pre-coding:

Did you try editing the Werte values or using the checkboxes you see on the right in your screenshot?

[Deja_Vu]

I've done both - I did verify though that the Werte values were set correctly after using the checkboxes. The issue is the FDL is showing the correct values when I code - however after re-reading the coding data it has been switched back. It's like the value is stuck in read-only but no errors are thrown because of it. After dinner I'm going to try coding something else and see if those values stick or not.

[dmnc02]

Originally Posted by Deja_Vu

I've done both - I did verify though that the Werte values were set correctly after using the checkboxes. The issue is the FDL is showing the correct values when I code - however after re-reading the coding data it has been switched back. It's like the value is stuck in read-only but no errors are thrown because of it. After dinner I'm going to try coding something else and see if those values stick or not.

That is odd. You probably already know this, but if you edit the Werte values directly, remember to click on the symbol I have circled in red in order to transfer the edited Werte to the CAFD before saving it.

[Deja_Vu]

Omg...so I figured it out. I would always right-click and *think* I was coding the FDL. However I was just coding the the CAFD folder/ECU sometimes because I didn't click the CAFD file directly. Doh! Freakin software developer and I screwed that up.

[dmnc02]

Originally Posted by Deja_Vu

Doh! Freakin software developer and I screwed that up.

You can always blame the poor GUI work of the E-Sys software developer.

If you do not use the checkboxes, remember to do the same change (i.e., replace the "64" in the 5th position with "00") in TMS > Welcome Light 1.

[JTO24]

Guys, I had coding done prior to myself picking up a cable and coding on my own. My previous coding had the 3 amber lights coded off when I unlocked the doors so only the angel eyes and eyebrows lit.

I did do the correct Euro LED headlights (friggin love it now!!!) so I had to VO code both TMS's. I coded off the 3 amber lights when the headlights are on (per instructions in this thread) but now the 3 amber lights come on when I unlock the doors.

Does anyone know how to code out the 3 amber lights for when the doors unlock? I could go through each line 1 by 1 in the TMS modules but I don't want to change a werte value that will screw something up.

[dmnc02]

Originally Posted by JTO24

Guys, I had coding done prior to myself picking up a cable and coding on my own. My previous coding had the 3 amber lights coded off when I unlocked the doors so only the angel eyes and eyebrows lit.

I did do the correct Euro LED headlights (friggin love it now!!!) so I had to VO code both TMS's. I coded off the 3 amber lights when the headlights are on (per instructions in this thread) but now the 3 amber lights come on when I unlock the doors.

Does anyone know how to code out the 3 amber lights for when the doors unlock? I could go through each line 1 by 1 in the TMS modules but I don't want to change a werte value that will screw something up.

See the post just above yours.

[JTO24]

Originally Posted by dmnc02

See the post just above yours.

lol doh!! thanks.. I need to read more carefully

[Henriki]

Has anyone tried coding out the 3 small amber leds with carly or bimmercode?

[taint]

Originally Posted by Henriki

Has anyone tried coding out the 3 small amber leds with carly or bimmercode?

I use bimmercode a bit for a quick change of settings. In my experience it doesn't allow this level of changes. It really just does basic convenience things. You need to be able to change the Werte values, which I haven't found bimmercode able to do.

Now, since I have a 2018 with LEDs I don't have the TMS module. Still trying to code mine off...

[E90bedi]

Originally Posted by Boostin FD

Has anyone successfully coded out those amber little leds in the headlights? I'm not a fan of Amber light and had it disabled before on my e92 M3... For some reason the code posted for the F8X doesn't work.

Has anyone done it yet?

Yes very easy, PM me

[taint]

Originally Posted by E90bedi

Yes very easy, PM me

You have to change werte values in both FLE ECUs, 10 to be exact. Just got mine off all the time. PM me and I can help you out.

[M BROK3]

Originally Posted by dmnc02

See the post just above yours.

Any idea on how to do this for 2018 m3 which doesn’t have tms modules anymore?

[Rid3r]

Originally Posted by M BROK3

Any idea on how to do this for 2018 m3 which doesn’t have tpms modules anymore?

+1 looking for this info also

[JDougM3]

https://github.com/packetpilot/bmw-f...ats/Kip_M3.xml

[Rid3r]

Originally Posted by JDougM3

https://github.com/packetpilot/bmw-f...ats/Kip_M3.xml

That for TMS module ... the 2018 doesn't have the tms ecu any more

[pmooiweer]

Originally Posted by Rid3r

That for TMS module ... the 2018 doesn't have the tms ecu any more

Use my cheat codes for MY18: https://github.com/packetpilot/bmw-f/blob/master/pmooiweer

[grilodan]

I coded my F86 and it worked using this in both FLE ECU’s:

SIDEMRKLGT_Idx:
Change to 01_VALUE so werte reads only 00’s

LM_ID_LT04:
02_Value = 00

LM04_NAME:
02_Value = 00

[F80_BK]

Originally Posted by Henriki

Has anyone tried coding out the 3 small amber leds with carly or bimmercode?

Yes. I just did it with bimmercode app and worked perfect to get rid of the 3 corner LEDs. Both TMS modules (right and left) need to be coded.

TMS03 (left)
-Choose section 3005.
-Standlicht Modus 1 and click on F10_524_ECE so there is a check mark next to it.
-Click the Back button and do the same for Standlicht Modus 2.
-Click the Back button and do the same for Welcome Light 1 (if you want the 3 LEDs off when unlocking).
-Click the Back button twice and hit Code in top right.

Repeat for TMS03 (right)

[Toad535]

Originally Posted by aboulfad

After coding:

It's been a very long time, but can to clarify what you coded for the halogen bulbs in xenon lights to turn them off? I have an F25 and can't figure it out.