@shawnsheridan, some errors at the end of TAL execution, is it again the stupid ignition ? or a dependency? This is when i was flashing EGS, GHAS, VDC. car is alive though but with the usual transport mode and faults.
Code:
MCDDiagService<id=46900, job=com.bmw.psdz.jobs.uds.MCD3_GetSVKfromECU, service=RDBI_SVK - ReadDataByIdentifier SVK, description=error: timeout, link=Physical request to ECU with address 0xf>
MCDDiagService<id=46900, job=com.bmw.psdz.jobs.uds.MCD3_GetSVKfromECU, service=RDBI_SVK - ReadDataByIdentifier SVK, description=error: timeout, link=Physical request to ECU with address 0xf>
MCDDiagService<id=46900, job=com.bmw.psdz.jobs.uds.MCD3_GetSVKfromECU, service=RDBI_SVK - ReadDataByIdentifier SVK, description=error: timeout, link=Physical request to ECU with address 0xf>
[GHAS - F] There was an error during TAL execution, please check the log files.
[GHAS - F] - [Exception - GHAS - f] negative response error:
code: TIMEOUT P2/T2 occurred
description: P2 timeout on Service RDBI_SVK has error in result: [Severity=2051][ErrorCode=58640][ErrorCodeDescription=resource not available][VendorCode=2142][VendorCodeDescription=P2 timeout occured]; ECU: GHAS_0F_ETHERNET
severity: ERROR
MCDDiagService<id=80900, job=com.bmw.psdz.jobs.uds.MCD3_FinalizeECUCoding, service=WDBI_CPS - WriteDataByIdentifier Codierpruefstempel, description=error: timeout, link=Physical request to ECU with address 0x76>
MCDDiagService<id=80900, job=com.bmw.psdz.jobs.uds.MCD3_FinalizeECUCoding, service=WDBI_CPS - WriteDataByIdentifier Codierpruefstempel, description=error: timeout, link=Physical request to ECU with address 0x76>
MCDDiagService<id=80900, job=com.bmw.psdz.jobs.uds.MCD3_FinalizeECUCoding, service=WDBI_CPS - WriteDataByIdentifier Codierpruefstempel, description=error: timeout, link=Physical request to ECU with address 0x76>
MCDDiagService<id=230900, job=com.bmw.psdz.jobs.uds.MCD3_FinalizeECUCoding, service=DSC - DiagnosticSessionControl, description=error: timeout, link=Physical request to ECU with address 0x76>
[VDC1 - 76] finalizeECUCoding error
[VDC1 - 76] There was an error during TAL execution, please check the log files.
[VDC1 - 76] - [Exception - VDC1 - 76] negative response error:
code: TIMEOUT P2/T2 occurred
description: P2 timeout on Service DSC has error in result: [Severity=2051][ErrorCode=58640][ErrorCodeDescription=resource not available][VendorCode=2142][VendorCodeDescription=P2 timeout occured]; ECU: VDC1_76_ETHERNET
severity: ERROR
[] finalizeVehicleCoding started
[] finalizeVehicleCoding finished
[] finalizeTALExecution started
[] finalizeTALExecution finished
TAL execution finished
TAL-Execution finished with status: "FinishedWithError". [C207]
TAL execution finished. Duration: "6min 55s". [C206]