F80 M3 Center Console Issue

Mnu032 · 05-17-2024, 10:57 PM

Recently noticed a corner lifting on the carbon fiber center console trim. I lifted the corner with barely any effort and it completely separated

. not sure if any one else has dealt with this. Any suggestions on repairing it? is there a certain adhesive I have to apply? or am I better off just looking for a replacement?

Danlnyc88 · 05-17-2024, 11:07 PM

I would just apply some jbweld and call it a day

b_w. · 05-18-2024, 09:40 AM

That is annoying. Just glue it back on. I would use super glue.

M3SQRD · 05-18-2024, 10:09 AM

I’d also use super glue or a Gorilla Glue general purpose adhesive. I’d apply it to the entire top surface of the still attached piece, a single line of glue on the vertical faces and leave a decent gap around the Idrive controller. The gap is so glue can’t whisk up onto the top surface of the CF cover.

Yuille36 · 05-22-2024, 09:28 AM

I would remove the attached panel piece, then use some aggressive sand paper to rough up the surface to not only get rid of the old glue, but provide the new glue with something to bite into. As far as glue goes, I would use something that has with really good bonding strength. I would also purchase a few clamps to sandwich the two pieces together. Just my thoughts

sergbaja5t · 05-24-2024, 11:56 AM

We are forgetting, to find a glue with tolerance to high heat.

Yuille36 · 05-24-2024, 12:03 PM

That is a dam good point, as our cars interior can reach well over 150 degrees in the direct summer sun.

M3SQRD · 05-24-2024, 04:23 PM

First, roughing up the surfaces for bonding is a great idea. After completing the roughing up procedure, wipe it down with Simple Green to remove any oil contaminants and debris.

Second, if you’re concerned with interior temps, use an epoxy glue/adhesive which can handle temps up to 300 deg F.

NSX2M4 · 05-25-2024, 04:28 PM

I'd just replace the damn thing. It's obviously a faulty part. This piece is maybe 260 bucks and you touch it everyday.

05-17-2024, 10:57 PM	#1
Mnu032 Registered 0 Rep 1 Posts Drives: 2016 BMW M3 Join Date: May 2024 Location: Tampa iTrader: (0)	F80 M3 Center Console Issue Recently noticed a corner lifting on the carbon fiber center console trim. I lifted the corner with barely any effort and it completely separated . not sure if any one else has dealt with this. Any suggestions on repairing it? is there a certain adhesive I have to apply? or am I better off just looking for a replacement? Attached Images
	Appreciate 0 Tweet Quote

05-17-2024, 11:07 PM	#2
Danlnyc88 Captain 502 Rep 670 Posts Drives: 2020 M4 Comp, 2017 Macan Turbo Join Date: Jun 2019 Location: Orange County iTrader: (1)	I would just apply some jbweld and call it a day
	Appreciate 0 Quote

05-18-2024, 09:40 AM	#3
b_w. Captain 621 Rep 740 Posts Drives: ST F80 M3 GT More 6 SPD, F90 C Join Date: Jul 2022 Location: Alberta iTrader: (1)	That is annoying. Just glue it back on. I would use super glue.
	Appreciate 0 Quote

05-18-2024, 10:09 AM	#4
M3SQRD Major General 3384 Rep 7,052 Posts Drives: E92 M3,G20 330ix,F22 240iX,F82 Join Date: Jun 2009 Location: Mid-Atlantic iTrader: (12)	I’d also use super glue or a Gorilla Glue general purpose adhesive. I’d apply it to the entire top surface of the still attached piece, a single line of glue on the vertical faces and leave a decent gap around the Idrive controller. The gap is so glue can’t whisk up onto the top surface of the CF cover.
	Appreciate 0 Quote

05-22-2024, 09:28 AM	#5
Yuille36 Major 620 Rep 1,270 Posts Drives: X5M, M3 ZCP 6MT, MB E63 AMG Join Date: Dec 2019 Location: Alexandria, VA iTrader: (0) Garage List 2015 BMW X5M [9.83] 2017 BMW/M3 [9.90]	I would remove the attached panel piece, then use some aggressive sand paper to rough up the surface to not only get rid of the old glue, but provide the new glue with something to bite into. As far as glue goes, I would use something that has with really good bonding strength. I would also purchase a few clamps to sandwich the two pieces together. Just my thoughts __________________ *It is never taken for granted that a commitment to speed and acceleration must be matched with an equivalent ambition when it comes time to stop!*
	Appreciate 1 SteveYem227.50 Quote

05-24-2024, 11:56 AM	#6
sergbaja5t Private First Class 63 Rep 157 Posts Drives: 2011 E92-M3 Comp Join Date: Feb 2013 Location: United States iTrader: (0)	We are forgetting, to find a glue with tolerance to high heat.
	Appreciate 0 Quote

05-24-2024, 12:03 PM	#7
Yuille36 Major 620 Rep 1,270 Posts Drives: X5M, M3 ZCP 6MT, MB E63 AMG Join Date: Dec 2019 Location: Alexandria, VA iTrader: (0) Garage List 2015 BMW X5M [9.83] 2017 BMW/M3 [9.90]	That is a dam good point, as our cars interior can reach well over 150 degrees in the direct summer sun. __________________ *It is never taken for granted that a commitment to speed and acceleration must be matched with an equivalent ambition when it comes time to stop!*
	Appreciate 0 Quote

05-24-2024, 04:23 PM	#8
M3SQRD Major General 3384 Rep 7,052 Posts Drives: E92 M3,G20 330ix,F22 240iX,F82 Join Date: Jun 2009 Location: Mid-Atlantic iTrader: (12)	First, roughing up the surfaces for bonding is a great idea. After completing the roughing up procedure, wipe it down with Simple Green to remove any oil contaminants and debris. Second, if you’re concerned with interior temps, use an epoxy glue/adhesive which can handle temps up to 300 deg F.
	Appreciate 0 Quote

05-25-2024, 04:28 PM	#9
NSX2M4 Lieutenant Colonel 1594 Rep 1,505 Posts Drives: 2019 M4 ZCP- RIVIAN R1S QUAD Join Date: Jun 2019 Location: FTL, FL iTrader: (1)	I'd just replace the damn thing. It's obviously a faulty part. This piece is maybe 260 bucks and you touch it everyday. __________________ MGM Ext, SO int, Euro IKON, CS front lip, Carbon 1.5 diffuser, GTS/CS coding, M perf rear spoiler, & everything else STOCK. (Previous E39 and NA1 NSX owner) Those were the days!
	Appreciate 0 Quote