E-Sys 3.30.1 & ESYS Launcher PRO 2.8.1 + Cheat Sheets/Guides *DIY*

[shawnsheridan]

Originally Posted by Benas09

So, do I understand correct, that it is not important which version to use to write vin and fsc codes to my new head unit?

And it will be be enough to get back working PDC, bluetooth, navigation and other functions I originally had?

When I connected new head unit, there was very similar menu in screen (PDC worked, bluetooth was shown, but did no connected). After couple ignitions of engine, almost all menu disappeared (I believe due to vin mismatch with car and headunit?)

You can use the latest E-Sys if that is what you are asking.

There are many factors here. Besides what I wrote above about Launcher PRO limiting E-Sys, you also have to consider that Injecting CAFD (Detect CAF for SWE) and Flashing ECU's with >= v.4.17.20 PSdZData requires using newer E-Sys 3.30.0 or higher, so you will need at least E-Sys 3.30.0.

You need to install Donor Head Unit, wipe donor FSC Codes if newer than your VIN matching ones, then import your VIN matching ones, then Inject CAFD into HU_ENTRYNAV, and VO Code it.

[Benas09]

I am very grateful for your time.

Is it enough that I only have original fsc files or fsc certificates will be needed also?

My old headunit boots (it is internal amp fried, I dissasembled it a little and made sure), so I think it would be possible to backup original certificates also if needed.

[shawnsheridan]

Originally Posted by Benas09

I am very grateful for your time.

Is it enough that I only have original fsc files or fsc certificates will be needed also?

My old headunit boots (it is internal amp fried, I dissasembled it a little and made sure), so I think it would be possible to backup original certificates also if needed.

For each FSC Code, you need original .der and .fsc files, although same .der can be used for all.

[Benas09]

.der files are also stored in head unit and I have to connect my original head unit back to the car to read these, yes?

[shawnsheridan]

Originally Posted by Benas09

.der files are also stored in head unit and I have to connect my original head unit back to the car to read these, yes?

I don't think so. Need original OEM FSC Code set.

[514Bimmergang]

Originally Posted by shawnsheridan

PM sent.

I'm having the same exact issue, using E-Sys Launcher Pro V2.8.2.162 I'm getting a pop up message quote "Ivalid EST Token". Note: password I'm using us 12345678 as indicated on the message.

[Benas09]

This token is not valid anymore (it was valid till 2022-06).
As shawnsheridan said, you can use v2.8.1 launcher with E-Sys 3.30 (this launcher still has valid token). I have succesfully installed this yesterday. You can download it from #1 post of this tread.

[Benas09]

Hello again, shawnsheridan.

As you wrote, I have to inject CAFD into HU_ENTRYNAV. I guess that full psdzdata is required for this task.

Now I have working e-sys 3.30.1 from this thread #1 with v.4.27.20_PSdZData_Lite from the internet.

I also found v.60.1_SP-Daten which looks as in picture below. I have downloaded BASE and F020 and extracted these. Are these valid psdzdata or not? When I remove existing psdzdata lite files and pasting these, I dont see any available target in connection window.

Currently I am downloading v.4.37.20_PSdZData_Full.7z (88.72 GB), in case these I have are bad.

And do I have to take some specific version of psdzdata or any version will be ok? I heard about I-step but I dont know if it is important for my use case.

[kubax86]

Originally Posted by Benas09

Hello again, shawnsheridan.

As you wrote, I have to inject CAFD into HU_ENTRYNAV. I guess that full psdzdata is required for this task.

Now I have working e-sys 3.30.1 from this thread #1 with v.4.27.20_PSdZData_Lite from the internet.

I also found v.60.1_SP-Daten which looks as in picture below. I have downloaded BASE and F020 and extracted these. Are these valid psdzdata or not? When I remove existing psdzdata lite files and pasting these, I dont see any available target in connection window.

Currently I am downloading v.4.37.20_PSdZData_Full.7z (88.72 GB), in case these I have are bad.

And do I have to take some specific version of psdzdata or any version will be ok? I heard about I-step but I dont know if it is important for my use case.

psdzdata lite is enough
latest version is fine
extract using 7zip or winter

[Benas09]

Hello kubax86.

So I downloaded v.4.37.42_PSdZData_Lite-BU.
I just now wrote VIN to head unit and injected CAFD by doing steps given by shawnsheridan.

Everything worked smoothly and by first sight everything became working again - PDC, radio, bluetooth connection and streaming, all menus. Except navigation - it is grayed out now.
Startup sceen is different (now it is bmw connected drive or something similar, before it was m sport animation), but nevermind for now.

What I noticed, that it was different CAFD version (or creation date?) that my cars i-step.
Is it ok or it should be and could by updated? See attached images.

To get navigation back again - I have to buy somewhere OEM FSC codes? I didn't do anything with FSC yet.

Thank you again both shawnsheridan and kubax86

[StanislavH]

Please give a link to download v.4.37.42 PSdZData Lite thanks in advance!

[kubax86]

Originally Posted by Benas09

Hello kubax86.

So I downloaded v.4.37.42_PSdZData_Lite-BU.
I just now wrote VIN to head unit and injected CAFD by doing steps given by shawnsheridan.

Everything worked smoothly and by first sight everything became working again - PDC, radio, bluetooth connection and streaming, all menus. Except navigation - it is grayed out now.
Startup sceen is different (now it is bmw connected drive or something similar, before it was m sport animation), but nevermind for now.

What I noticed, that it was different CAFD version (or creation date?) that my cars i-step.
Is it ok or it should be and could by updated? See attached images.

To get navigation back again - I have to buy somewhere OEM FSC codes? I didn't do anything with FSC yet.

Thank you again both shawnsheridan and kubax86

Need to delete old FSC and inject new ones.
If you need assistance you can PM me

[Benas09]

I did not delete fsc codes, only wrote new and everything works again. There is a thread I created about my issue https://f30.bimmerpost.com/forums/sh....php?t=1961034

Thank you for helping 😊

[Benas09]

Originally Posted by StanislavH

Please give a link to download v.4.37.42 PSdZData Lite thanks in advance!

I dont know if forum rules allow to share links to other forums. You should easily find. Download link is free, you just have to register to other forum and reply to thread to get link unlocked.

As your pm is not working yet, I can send you download link to email if you want.

[StanislavH]

Originally Posted by Benas09

I dont know if forum rules allow to share links to other forums. You should easily find. Download link is free, you just have to register to other forum and reply to thread to get link unlocked.

As your pm is not working yet, I can send you download link to email if you want.

I would be very grateful. Thanks! staniiiiislav@gmail.com

[Benas09]

Ok, sent

[StanislavH]

Originally Posted by Benas09

Ok, sent

Thanks a lot

[Metalm4]

My launcher doesn´t work anymore. And re-installing always shows "Invalid token". I deleted each e-sys version and launcher version and also cleared the registry, but i don´t get it running
Any idea?

Originally Posted by Benas09

This token is not valid anymore (it was valid till 2022-06).
As shawnsheridan said, you can use v2.8.1 launcher with E-Sys 3.30 (this launcher still has valid token). I have succesfully installed this yesterday. You can download it from #1 post of this tread.

[Benas09]

Are you trying to launch
v2.8.1 launcher with E-Sys 3.30 with token given at this thread 1st post?

I am new user of this software, so I dont know if there are any leftovers after deleting all esys files.
Maybe some left, for example in C:\Users\<username>\AppData?

I am using esys in virtual machine. If you will not figure it out, you can try that also.

EDIT:
I found these folders
C:\Users\<username>\AppData\Local\TokenMaster
C:\Users\<username>\AppData\Roaming\TokenMaster
C:\EC-Apps
C:\Program Files (x86)\TokenMaster
C:\ProgramData\TokenMaster

[StanislavH]

Originally Posted by Benas09

Are you trying to launch
v2.8.1 launcher with E-Sys 3.30 with token given at this thread 1st post?

I am new user of this software, so I dont know if there are any leftovers after deleting all esys files.
Maybe some left, for example in C:\Users\<username>\AppData?

I am using esys in virtual machine. If you will not figure it out, you can try that also.

EDIT:
I found these folders
C:\Users\<username>\AppData\Local\TokenMaster
C:\Users\<username>\AppData\Roaming\TokenMaster
C:\EC-Apps
C:\Program Files (x86)\TokenMaster
C:\ProgramData\TokenMaster

Try Everything to search for leftover files/folders (run as administrator)
and also here is the removal guide:
https://www.wikihow.com/Delete-a-Pro...stry-(Windows)
https://www.advanceduninstaller.com/...pplication.htm
P.S.
I hope I'm not violating forum rules by adding this article?

[F32rocket]

Hi, I am new to this. I want to 'VO code' various modules on my car, do I need psdzdata Full or Lite version? For VO coding, do I need to open the "launcher pro" app before e-sys?

[shawnsheridan]

Originally Posted by F32rocket

Hi, I am new to this. I want to 'VO code' various modules on my car, do I need psdzdata Full or Lite version? For VO coding, do I need to open the "launcher pro" app before e-sys?

For VO Coding, you need ONLY E-Sys and psdzsdata Lite.