[CODING] Missing CAFD Files

shawnsheridan · 02-18-2019, 12:41 PM

Quote:

Originally Posted by svhout

That was also what i was thinking.
I followed the manual Rearview Camera Retrofit. Everything was according to the manual except for the cable A6 & A7 which i should have connected to the excisting cable on pin 51 & 52. There where no cables in there so i just plugged them in. I read that that should be no problem….
Perhaps you can find a fault in these?

I have no idea. As I wrote, I have never retrofitted Camera before.

svhout · 02-18-2019, 12:56 PM

Thanks anyway Shawn.

Perhaps somebody else has any idea?

svhout · 02-22-2019, 07:01 AM

Hi Shawn,

i found the problem. It was a faulty module. The TRSVC pops up now in Esys but has ofcourse no CAFD. When i want to select the right CAFD it doesn't show the one i need but only newer. See pictures.
If i select one of these the TRSVC and HU-NBT ECU turns red so i stopped and didn't code it to the car.
Is this normal and should i code it or should i find the right CAFD and where do i find it?

Grtzz,

Stefan

shawnsheridan · 02-22-2019, 07:21 AM

Quote:

Originally Posted by svhout

Hi Shawn,

i found the problem. It was a faulty module. The TRSVC pops up now in Esys but has ofcourse no CAFD. When i want to select the right CAFD it doesn't show the one i need but only newer. See pictures.
If i select one of these the TRSVC and HU-NBT ECU turns red so i stopped and didn't code it to the car.
Is this normal and should i code it or should i find the right CAFD and where do i find it?

Grtzz,

Stefan

Post picture of what has turned Red.

svhout · 02-22-2019, 07:36 AM

I connected again and now only the TRSVC turned red.

shawnsheridan · 02-22-2019, 07:37 AM

Quote:

Originally Posted by svhout

I connected again and now only the TRSVC turned red.

That's normal. VO Code it.

svhout · 02-22-2019, 12:28 PM

Yess,

it's loaded but i still have no view from the camera. Only a black screen in the middle with the buttons greyed out on the left site and the PDC on the right. Pffff still must have missed something….

Anybody?

svhout · 02-22-2019, 03:20 PM

Shawn,
could it be a problem that we coded the TRSVC with the F020-17-11-520 CAFD instead of the F020-15-03-504 which is standing in I-step (current)?

shawnsheridan · 02-22-2019, 03:27 PM

Quote:

Originally Posted by svhout

Shawn,
could it be a problem that we coded the TRSVC with the F020-17-11-520 CAFD instead of the F020-15-03-504 which is standing in I-step (current)?

CAFD itself is not a problem. If it were not compatable with the ECU's current firmware, it would not allow you to inject and Encode it to begin with.

Now, you can have good CAFD but bad Coding.

svhout · 02-23-2019, 04:27 AM

Yep, you're right Shawn. There was one setting which was not set correctly.
Now it's working

Thanks!!

Up to the next project => Top view

shawnsheridan · 02-23-2019, 10:02 AM

Quote:

Originally Posted by svhout

Yep, you're right Shawn. There was one setting which was not set correctly.
Now it's working

Thanks!!

Up to the next project => Top view

Molinetti · 05-03-2019, 03:33 AM

Hi all,

First of all thank you for your activity, I'm learning a lot with your messages and support!
shawnsheridan I googled my problem and I have seen that you are an expert in Esys... I described you my problem. Coding with bmwaicoder my HU NBT EVO 2, writing fail and then I lost CAFD in the ECU, I tried to restore CAFD with esys also writting it fails. Is there something more to do with esys or I need to reflash the NBT? Thanks in advance!

shawnsheridan · 05-03-2019, 07:32 AM

Quote:

Originally Posted by Molinetti

Hi all,

First of all thank you for your activity, I'm learning a lot with your messages and support!
shawnsheridan I googled my problem and I have seen that you are an expert in Esys... I described you my problem. Coding with bmwaicoder my HU NBT EVO 2, writing fail and then I lost CAFD in the ECU, I tried to restore CAFD with esys also writting it fails. Is there something more to do with esys or I need to reflash the NBT? Thanks in advance!

You need to re-flash it.

enes28 · 10-14-2019, 07:18 AM

Hello

Can you send me a cafd 00000794 002 020 029 files ?

I found a few links but it was dead.

Thanks in advance

shawnsheridan · 10-14-2019, 07:49 AM

Quote:

Originally Posted by enes28

Hello

Can you send me a cafd 00000794 002 020 029 files ?

I found a few links but it was dead.

Thanks in advance

Try latest v.4.19.40 PSdZData. PM sent.

perikoo · 01-19-2020, 09:06 AM

Hi everyone,

trying to code the FEM_BODY I always get the error
CAFD_00000794_018_070_004 Fehler:
File for "cafd_00000794-018_070_004" not found! [C012]

I then read the I-Steps and got this:

I-Step (current): F020-19-11-530
I-Step (last): F020-17-11-540
I-Step (shipment): F020-13-11-504

I dont know what to do next to fix this problem.

I had the EGR cooler replaced 2 months ago, and also in the BMW dealer they told me that they had upgraded the system. Could this has something to do with this error?
I am using Esys 3.28.1 and PSdZData_Lite_v4.17.20 with the Esys launcher Pro 2.8.2.

I was able to code the IDrive Logo but I can not access to FEM_BODY nor to KOMBI.

Any help would be very welcome!

Thanks in advance

kubax86 · 01-19-2020, 10:18 AM

Quote:

Originally Posted by perikoo

Hi everyone,

trying to code the FEM_BODY I always get the error
CAFD_00000794_018_070_004 Fehler:
File for "cafd_00000794-018_070_004" not found! [C012]

I then read the I-Steps and got this:

I-Step (current): F020-19-11-530
I-Step (last): F020-17-11-540
I-Step (shipment): F020-13-11-504

I dont know what to do next to fix this problem.

I had the EGR cooler replaced 2 months ago, and also in the BMW dealer they told me that they had upgraded the system. Could this has something to do with this error?
I am using Esys 3.28.1 and PSdZData_Lite_v4.17.20 with the Esys launcher Pro 2.8.2.

I was able to code the IDrive Logo but I can not access to FEM_BODY nor to KOMBI.

Any help would be very welcome!

Thanks in advance

You need latest psdzdata

shawnsheridan · 01-19-2020, 10:31 AM

Quote:

Originally Posted by perikoo

Hi everyone,

trying to code the FEM_BODY I always get the error
CAFD_00000794_018_070_004 Fehler:
File for "cafd_00000794-018_070_004" not found! [C012]
...

PM sent.

perikoo · 01-25-2020, 01:05 PM

Thanks again Shawnsheridan, with this psdzdata everything worked as expected and I was able to code the FEM_BODY and the KOMBI folders.
I have to mention that the psdzdata gave me an error during the extraction of the rar file.
I downloaded it three times and it always gave me the same error, but the extraction continued and the psdzdata folder created worked well as I mentioned above.

Cheers

shawnsheridan · 01-25-2020, 01:08 PM

Quote:

Originally Posted by perikoo

Thanks again Shawnsheridan, with this psdzdata everything worked as expected and I was able to code the FEM_BODY and the KOMBI folders.
I have to mention that the psdzdata gave me an error during the extraction of the rar file.
I downloaded it three times and it always gave me the same error, but the extraction continued and the psdzdata folder created worked well as I mentioned above.

Cheers

You should not have any extraction error if using latest version of 7-Zip or WinRAR.

fteixeira · 02-23-2020, 07:37 PM

Shawn: I ready thru this thread. Thank you for the tremendous help to the communitys.

I'm new to E-Sys coding and I want to make sure I have the proper pieces of software and do the installation properly. Just did the shadowline LCI taillight retrofit on my 2016 F83 and need to code. I sent you a PM. Hopefully you can help.

shawnsheridan · 02-23-2020, 07:44 PM

Quote:

Originally Posted by fteixeira

Shawn: I ready thru this thread. Thank you for the tremendous help to the communitys.

I'm new to E-Sys coding and I want to make sure I have the proper pieces of software and do the installation properly. Just did the shadowline LCI taillight retrofit on my 2016 F83 and need to code. I sent you a PM. Hopefully you can help.

I replied.

02-18-2019, 12:56 PM	#288
svhout New Member 0 Rep 14 Posts Drives: BMW F31 Join Date: Jul 2018 Location: Hengelo iTrader: (0)	Thanks anyway Shawn. Perhaps somebody else has any idea?
	Appreciate 0 Quote

02-22-2019, 07:01 AM	#289
svhout New Member 0 Rep 14 Posts Drives: BMW F31 Join Date: Jul 2018 Location: Hengelo iTrader: (0)	Hi Shawn, i found the problem. It was a faulty module. The TRSVC pops up now in Esys but has ofcourse no CAFD. When i want to select the right CAFD it doesn't show the one i need but only newer. See pictures. If i select one of these the TRSVC and HU-NBT ECU turns red so i stopped and didn't code it to the car. Is this normal and should i code it or should i find the right CAFD and where do i find it? Grtzz, Stefan Attached Images
	Appreciate 0 Quote

02-22-2019, 07:36 AM	#291
svhout New Member 0 Rep 14 Posts Drives: BMW F31 Join Date: Jul 2018 Location: Hengelo iTrader: (0)	I connected again and now only the TRSVC turned red. Attached Images
	Appreciate 0 Quote

02-22-2019, 12:28 PM	#293
svhout New Member 0 Rep 14 Posts Drives: BMW F31 Join Date: Jul 2018 Location: Hengelo iTrader: (0)	Yess, it's loaded but i still have no view from the camera. Only a black screen in the middle with the buttons greyed out on the left site and the PDC on the right. Pffff still must have missed something…. Anybody? Attached Images Last edited by svhout; 02-22-2019 at 01:31 PM..
	Appreciate 0 Quote

02-22-2019, 03:20 PM	#294
svhout New Member 0 Rep 14 Posts Drives: BMW F31 Join Date: Jul 2018 Location: Hengelo iTrader: (0)	Shawn, could it be a problem that we coded the TRSVC with the F020-17-11-520 CAFD instead of the F020-15-03-504 which is standing in I-step (current)?
	Appreciate 0 Quote

02-23-2019, 04:27 AM	#296
svhout New Member 0 Rep 14 Posts Drives: BMW F31 Join Date: Jul 2018 Location: Hengelo iTrader: (0)	Yep, you're right Shawn. There was one setting which was not set correctly. Now it's working Thanks!! Up to the next project => Top view
	Appreciate 0 Quote

05-03-2019, 03:33 AM	#298
Molinetti Private 5 Rep 63 Posts Drives: BMW 428i Join Date: May 2019 Location: Madrid, Spain iTrader: (0)	Hi all, First of all thank you for your activity, I'm learning a lot with your messages and support! shawnsheridan I googled my problem and I have seen that you are an expert in Esys... I described you my problem. Coding with bmwaicoder my HU NBT EVO 2, writing fail and then I lost CAFD in the ECU, I tried to restore CAFD with esys also writting it fails. Is there something more to do with esys or I need to reflash the NBT? Thanks in advance!
	Appreciate 0 Quote

10-14-2019, 07:18 AM	#300
enes28 Private 3 Rep 60 Posts Drives: Polo TSI Join Date: Apr 2017 Location: Turkey iTrader: (0)	Hello Can you send me a cafd 00000794 002 020 029 files ? I found a few links but it was dead. Thanks in advance
	Appreciate 0 Quote

01-19-2020, 09:06 AM	#302
perikoo Registered 2 Rep 4 Posts Drives: Corsa GSi MK1 and F20 125d Join Date: May 2019 Location: Spain iTrader: (0)	Problemwith FEM_BODY Hi everyone, trying to code the FEM_BODY I always get the error CAFD_00000794_018_070_004 Fehler: File for "cafd_00000794-018_070_004" not found! [C012] I then read the I-Steps and got this: I-Step (current): F020-19-11-530 I-Step (last): F020-17-11-540 I-Step (shipment): F020-13-11-504 I dont know what to do next to fix this problem. I had the EGR cooler replaced 2 months ago, and also in the BMW dealer they told me that they had upgraded the system. Could this has something to do with this error? I am using Esys 3.28.1 and PSdZData_Lite_v4.17.20 with the Esys launcher Pro 2.8.2. I was able to code the IDrive Logo but I can not access to FEM_BODY nor to KOMBI. Any help would be very welcome! Thanks in advance
	Appreciate 0 Quote

01-25-2020, 01:05 PM	#305
perikoo Registered 2 Rep 4 Posts Drives: Corsa GSi MK1 and F20 125d Join Date: May 2019 Location: Spain iTrader: (0)	Thanks again Shawnsheridan, with this psdzdata everything worked as expected and I was able to code the FEM_BODY and the KOMBI folders. I have to mention that the psdzdata gave me an error during the extraction of the rar file. I downloaded it three times and it always gave me the same error, but the extraction continued and the psdzdata folder created worked well as I mentioned above. Cheers
	Appreciate 0 Quote

02-23-2020, 07:37 PM	#307
fteixeira New Member 0 Rep 10 Posts Drives: 2016 M4 Convertible - BSM Join Date: Jan 2019 Location: SF Bay Area CA iTrader: (0)	Shawn: I ready thru this thread. Thank you for the tremendous help to the communitys. I'm new to E-Sys coding and I want to make sure I have the proper pieces of software and do the installation properly. Just did the shadowline LCI taillight retrofit on my 2016 F83 and need to code. I sent you a PM. Hopefully you can help.
	Appreciate 0 Quote