02-12-2017, 10:41 PM | #111 | |
Major General
2374
Rep 8,364
Posts |
Quote:
Did you write updated SVT to VCM? |
|
Appreciate
0
|
02-12-2017, 10:53 PM | #113 |
Major General
2374
Rep 8,364
Posts |
|
Appreciate
0
|
02-12-2017, 11:13 PM | #116 |
Major General
2374
Rep 8,364
Posts |
|
Appreciate
0
|
02-12-2017, 11:28 PM | #117 |
Captain
483
Rep 812
Posts |
The most current PSDZ from Shawn. Current and last shows Nov 2015. About to give my baby girl a bath. I'll recalculate right after and report back.
Thank you. |
Appreciate
0
|
02-13-2017, 12:00 AM | #118 |
Captain
483
Rep 812
Posts |
PSDZ is I-step version 16-11-502.
Current is 15-11-501 Shipment and Last is 15-07-504. Sure enough I have a few ECU's that are wrong. ATM FEM Body and GW HU_NBT2 TMS (both) I'll flash these. Now to figure out the dependencies so I don't screw up again... |
Appreciate
0
|
02-13-2017, 12:19 AM | #119 |
Major General
2374
Rep 8,364
Posts |
F020-16-11-503 is the latest
|
Appreciate
0
|
02-13-2017, 12:19 AM | #120 |
Captain
483
Rep 812
Posts |
Alright, so I went through the steps and even though the ECU's don't match, they are not popping up under TAL-Processing.
Looks like I'll have to force them under TAL-Calculating. |
Appreciate
0
|
02-13-2017, 12:22 AM | #122 |
Major General
2374
Rep 8,364
Posts |
|
Appreciate
0
|
02-13-2017, 05:18 AM | #124 |
Brigadier General
1593
Rep 3,945
Posts
Drives: 2015 M4 MG/SO
Join Date: Mar 2014
Location: MTL, QC
|
Can you post a screenshot of the fault (or the code) from ISTA, what did ISTA propose under test measures? and did you also try the ABL "Teach in front electronic turn signal"?
Glad all your ECUs got flashed in the end! Last edited by aboulfad; 02-13-2017 at 05:38 AM.. |
Appreciate
0
|
02-13-2017, 11:16 PM | #125 | |
Captain
483
Rep 812
Posts |
Quote:
__________________
2016 Azurite Black F80 6MT
Last edited by psedog; 02-14-2017 at 02:08 AM.. |
|
Appreciate
0
|
02-14-2017, 02:18 AM | #126 |
Lieutenant Colonel
529
Rep 1,514
Posts |
You need to click on headlight modules LHM RHM whatever it was they are 4 and do some tests . I remember there was even fan test/teaching . Each module have some tabs , click on them and you will see what im talking about. There was order in which you have to do it so you may just do them twice . Like for left headlight its 2 modules so do module 1 then module 2 then 1 then 2 . Make sure you delete all errors before that. Dont have ISTA in front of me.
Edit its like teaching each single component insight of the headlight . That what worked for me when i replaced headlight. Hope this helps |
Appreciate
0
|
02-14-2017, 03:10 PM | #127 |
Captain
483
Rep 812
Posts |
dzvero,
I'm using Ista+ I just see the ABL initialize headlamps and teach turn signals. It's all in one. Here are some screen shots. Looks like I have plenty more errors than just the lights. Seems like com issues. Not really sure what to do about it. Turn signal error. All Error Messages
__________________
2016 Azurite Black F80 6MT
|
Appreciate
0
|
02-14-2017, 03:17 PM | #128 |
Brigadier General
1593
Rep 3,945
Posts
Drives: 2015 M4 MG/SO
Join Date: Mar 2014
Location: MTL, QC
|
Did you clear all faults post your flashing sessions? did you modify anything post your flashing sessions ? and do you know the status of the flashed ECUs ? try calculating TAL again and check in Esys that all ECUs show up properly in SVT tree.
PS: see attached ISTA pic for lighting service functions. PPS: Also, use ISTA "Call up ECU functions" in the Control Unit Tree to diagnose each ECU separately. Last edited by aboulfad; 02-14-2017 at 03:39 PM.. |
Appreciate
0
|
02-17-2017, 05:16 AM | #129 | |
Captain
483
Rep 812
Posts |
Quote:
I did not modify anything post flash. All ECU's show up fine. The ecu folder on a couple show up as red/blue, but the caf files show black and nothing shows up in TAL-Processing (I ran it anyway and the logs showed that it modified MSM, but no change to the issue). I've also reflashed those modules to try and correct it, but no luck. One of them was NBT2 (for some reason when ista is scanning it says NBTEVO). I've also tried changing the following in fem_body "MAPPING_SIDEMARKER_L_OUTPUT" and "MAPPING_SIDEMARKER_R_OUTPUT". From off to "fra_v_l" and "fra_v_r".
__________________
2016 Azurite Black F80 6MT
|
|
Appreciate
0
|
02-17-2017, 06:28 AM | #130 |
Brigadier General
1593
Rep 3,945
Posts
Drives: 2015 M4 MG/SO
Join Date: Mar 2014
Location: MTL, QC
|
@psedog , if you cleared through ISTA all faults post your last flashing session, and all those faults re-appear, then indeed there are issues. The fact that some ECUs show up as red/blue in Esys (assuming you used the same psdZ when you flashed and redid the SVT target), then that implies something wrong went with the flash.
Post a successful flash, if you redo the SVT target calc, all ECUs should not show any red/blue... I recommend you re-flash each individual ECU separately that still fails, so this way you can sort through the log files easier for errors. GL, and if you'd like I can help look at Esys psdZ logfile. So you have been driving your car without turn signals? PS: your mic 2 fault is probably related to you modifying your FA, you can code it out HU_NBT-> MICROPHONE_NUMBER = 1 |
Appreciate
0
|
02-17-2017, 12:23 PM | #131 | |
Captain
483
Rep 812
Posts |
Quote:
Edit: looks like only my passenger mirror signal works :
__________________
2016 Azurite Black F80 6MT
|
|
Appreciate
0
|
02-17-2017, 12:57 PM | #132 | |
Brigadier General
1593
Rep 3,945
Posts
Drives: 2015 M4 MG/SO
Join Date: Mar 2014
Location: MTL, QC
|
Quote:
Is your FEM ok? Diagnose one ECU at a time in ISTA as I mentioned above using "ECU call up" functions, they contain lots of service functions grouped per ECU. |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|