07-03-2021, 08:04 PM | #1 |
Major General
5367
Rep 5,111
Posts |
In preparation for some high boost on my being-built motor I picked up the EoS manifold. I asked for mine unpainted so I could work on it. The quality of CNC work outside on top is really nice, but the rough casting inside leaves a little to be desired. The seams have some casting residue and the runners could use a little cleanup.
Time to Smooth & Polish! This was my first time DIYing this job so I watched all the vids from HeadGames where Dave is hand porting heads. He's a master with great technique, so I copied his steady slow moves. My tools were a Dremel with flex-shaft, a China carbide burr set, and my Shop Vac. You have to take your time and work in small sections. If you go too fast you clog up your burr, and then it's done. In the pix you'll see me starting in the runners, first removing any casting leftovers or rough spots with the burrs. Then I sanded and brush polished. I also smoothed out the main opening where the throttle body mounts. I think the job turned out pretty good. If any of you guys want me to do this to your manifold send me a PM and we might work something out. Unboxing (basic kit without fueling)
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
07-03-2021, 08:05 PM | #2 |
Major General
5367
Rep 5,111
Posts |
Setting up the work space
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
Last edited by TopJimmy; 07-03-2021 at 08:16 PM.. |
Appreciate
0
|
07-03-2021, 08:07 PM | #3 |
Major General
5367
Rep 5,111
Posts |
Smoothing & Polishing
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
3
|
07-03-2021, 09:07 PM | #4 |
Captain
750
Rep 943
Posts |
Looking good bro but cleaning those runners is time consuming, too bad they don't clean up the manifold a little better. Some folks will argue that some roughness helps with mixing. I've been debating buying one for meth injection for that even distribution. Build looks top notch.
__________________
M4CS Frozen Blue
ARM DP's/Resonated Mid-pipe | SPL links | Hotchkis bars | JRZ RS2/camber plates | K&N | Koyorad HX | Powerflex purple | Rouge | Spiegler | Speed Eng. snorkel | Vargas CBC/hub | Wagner IC | xHP | Xpel stealth ppf |
Appreciate
0
|
07-03-2021, 09:36 PM | #5 | |
Major General
5367
Rep 5,111
Posts |
Quote:
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
|
Appreciate
0
|
07-05-2021, 09:59 PM | #7 |
Major General
5367
Rep 5,111
Posts |
Since a buddy asked about some work I picked up a couple more accessories to see how they did at smoothing out the inside surface of the manifold. One wheel does a really good job at removing surface garbage while leaving a rough enough texture to keep J-pipe spray from condensing.
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
1
guess2098515.00 |
07-06-2021, 09:17 AM | #8 |
BimmerPost Supporting Vendor
23673
Rep 189,834
Posts |
Nice
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
0
|
07-06-2021, 09:47 PM | #11 |
Major General
5367
Rep 5,111
Posts |
The objective of polishing is to allow the smoothest airflow. Smoothing inside corners helps reduce any turbulence.
Opening up the runners more would change the HP/TQ curves, but I don't mess around there.
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
0
|
07-09-2021, 10:56 AM | #12 |
Major General
5367
Rep 5,111
Posts |
Here's another EOS getting prepped for a buddy. His is painted clear so it gets a little extra attention on the prep work. He's not running any WMI before the manifold and requested a smooth polish inside.
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
0
|
07-09-2021, 12:19 PM | #14 |
Captain
750
Rep 943
Posts |
Looking good, you're becoming a pro .
__________________
M4CS Frozen Blue
ARM DP's/Resonated Mid-pipe | SPL links | Hotchkis bars | JRZ RS2/camber plates | K&N | Koyorad HX | Powerflex purple | Rouge | Spiegler | Speed Eng. snorkel | Vargas CBC/hub | Wagner IC | xHP | Xpel stealth ppf |
Appreciate
1
TopJimmy5367.00 |
07-10-2021, 09:31 PM | #15 |
Major General
5367
Rep 5,111
Posts |
Here's some eye candy for my man Ricky! His EOS' runners are smooth and shiny.
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
2
guess2098515.00 Detoxified202.50 |
07-11-2021, 05:26 PM | #18 |
Major General
5367
Rep 5,111
Posts |
Since I got some good practice working on my buddy's manifold it was time to redo mine. Now I used fine drums and brush wheels. I also worked the outside to remove the rough cast spots that their CNC can't get.
Next step…black CeraKote ceramic coating!
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
Last edited by TopJimmy; 07-11-2021 at 06:18 PM.. |
Appreciate
0
|
07-20-2021, 07:44 PM | #19 |
Major General
5367
Rep 5,111
Posts |
Here's another excellent application of black thermal ceramic by Bonehead Performance Coatings! It was only a Benjamin and a half.
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
3
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|