Support for GTS/ZCP related coding

[drroc]

Originally Posted by backagain

I think the confusion is that you are trying to FDL-code, but Almaretto is talking about VO coding.

I did my steering coding via FDL-coding by changing the parameter of "Variantencodierung Normal" in the EPS module. I played with different settings, and finally like the F82GTS setting the best - it is lighter and eliminates the dead zone in the middle.

Hope this helps.

That worked like a charm. Thanks! I guess I need to read up on VO coding on how to enable GTS MDM mode. I enabled euro MDM, and its marginally better compared to US MDM.

[backagain]

Originally Posted by drroc

That worked like a charm. Thanks! I guess I need to read up on VO coding on how to enable GTS MDM mode. I enabled euro MDM, and its marginally better compared to US MDM.

Let me know how that works.

[FSociety]

I coded EuroMDM, F87CS steering and now trying to find out if EDC for CS is F80_CRT ?
I am on latest 254 iStep level is there even such a thing as "CS" there's absolutely nothing
Confirmed also by cookiesowns

[Almaretto]

Originally Posted by FSociety

I coded EuroMDM, F87CS steering and now trying to find out if EDC for CS is F80_CRT ?
I am on latest 254 iStep level is there even such a thing as "CS" there's absolutely nothing
Confirmed also by cookiesowns

If you do not wish to use VO coding, then you can use E-sys Coding Verification to create NCD's and TM NCD / CAFD tool to compare and highlight change(s).

[cookiesowns]

Originally Posted by Almaretto

If you do not wish to use VO coding, then you can use E-sys Coding Verification to create NCD's and TM NCD / CAFD tool to compare and highlight change(s).

I'll have to give coding verification a go. Been using .32 esys for a little bit now, but will go back to .27 just for this.

Thanks! TM's NCD/CAFD tool is a life saver!

[Almaretto]

Originally Posted by cookiesowns

I'll have to give coding verification a go. Been using .32 esys for a little bit now, but will go back to .27 just for this.

Thanks! TM's NCD/CAFD tool is a life saver!

I only use 3.32.1_64bit for programming. I stick to 3.27.1 for coding for full functionality, including Coding-Verification and External Transmitter.

[6ixSpd]

Originally Posted by Almaretto

Change Chassis to F082 (not GTS).
Change Typecode to US or EU version of M4 GTS
EPS - Steering
GHAS - Differential
VDC - EDC

So doing the above and using 4S93 will get GTS steering and diff settings, but how would it change EDC as the GTS has a non-adpative setup? Also, would coding the EGS as well lead to GTS DCT changes?

Does one need the full PSDZdata or will Lite suffice?

Does anyone have a link to the PSDZ full?

[Almaretto]

Originally Posted by 6ixSpd

So doing the above and using 4S93 will get GTS steering and diff settings, but how would it change EDC as the GTS has a non-adpative setup? Also, would coding the EGS as well lead to GTS DCT changes?

Does one need the full PSDZdata or will Lite suffice?

Does anyone have a link to the PSDZ full?

Steering and Diff are in separate ECU's. So is VDC.

EGS is flashed with Full PSdzdata, not coded, which only requires light.

[6ixSpd]

Originally Posted by Almaretto

Steering and Diff are in separate ECU's. So is VDC.

EGS is flashed with Full PSdzdata, not coded, which only requires light.

Right, in your post on Page 1 you mentioned coding VDC. I am confused as to why. Wouldn't doing so message up the coding on an adaptive damper equipped F80?

And can the steering/diff be coded with the light version, only the EGS requires full?

[Almaretto]

Originally Posted by 6ixSpd

Right, in your post on Page 1 you mentioned coding VDC. I am confused as to why. Wouldn't doing so message up the coding on an adaptive damper equipped F80?

And can the steering/diff be coded with the light version, only the EGS requires full?

Some people think it performs better. Others say worse. It is all preference.

All coding can be done with Lite.
Only programming requires full.

[patman89]

Can anyone give indformation what FDL changes needs to be done when setting

- EPS
- GHAS
- DSC

to F82 M4 GTS ECE (4S91) to avoid VO coding?

[Almaretto]

Originally Posted by patman89

Can anyone give indformation what FDL changes needs to be done when setting

- EPS
- GHAS
- DSC

to F82 M4 GTS ECE (4S91) to avoid VO coding?

Do you have lots of FDL coding in those modules you do not want to have to recode after VO?

[kubax86]

Originally Posted by Robert0

Basic codings for GTS/CS:

DSC
CAFD_00001A33
3000 DSC_CODIERDATEN_ALLGEMEIN
Funktionen
C_Variante_Fahrzeug_e > Ausgelesen
"set/change to" -> F82_GTS

3000 DSC_CODIERDATEN_ALLGEMEIN
Funktionen
C_Funktion_RDCi_I > Ausgelesen
"set/change to" -> aktiv

*****************************

EPS
CAFD_00001A2F
3011 EPS_VEHICLE_VAR
Funktionen
Variantcodierung Normal > Ausgelesen
"set/change to" -> F82GTS

*****************************

GHAS
CAFD_000007C3
3000 DataSetSelector
Funktionen
DSS TASC > Ausgelesen
"set/change to" -> F082GTS

3000 DataSetSelector
Funktionen
DSS IPM > Ausgelesen
"set/change to" -> F082GTS

****************************

VDC1
CAFD_000006C6
3000 FAHRZEUGVARIANTE
Funktionen
Fahrzeugtyp > Ausgelesen
"set/change to" -> F85_Comp

3001 AUSSTATTUNGEN
Funktionen
M_Competition / High > Ausgelesen
"set/change to" -> nicht_aktiv

That was already posted. PDF Created by another user but thanks for your input.

[M4bad]

Originally Posted by kubax86

That was already posted. PDF Created by another user but thanks for your input.

I have searched for this pdf but couldnt find it, so those settings are helpful. Is there an ultimate end-all guide for GTS coding? Seems these threads are mainly folks testing alternate settings...

[Almaretto]

Originally Posted by M4bad

I have searched for this pdf but couldnt find it, so those settings are helpful. Is there an ultimate end-all guide for GTS coding? Seems these threads are mainly folks testing alternate settings...

1. Make sure update VCM is unchecked in E-sys Settings
2. Connect to Car
3. Read FA
4. Change Typecode (in FA) to GTS variant
5. Activate FA
6. Hold Control and select modules you wish to code
7. Select Code

[Almaretto]

Originally Posted by Robert0

And in this thread/post....

https://f80.bimmerpost.com/forums/sh...&postcount=177

i wrote a lot about flashing EGS4. With my M4 2020, changing FA to GTS doesn´t provide the appropriate swfl.

Never run into that issue, but you can always edit tal if needed.

[kubax86]

Originally Posted by Robert0

And in this thread/post....

https://f80.bimmerpost.com/forums/sh...&postcount=177

i wrote a lot about flashing EGS4. With my M4 2020, changing FA to GTS doesn´t provide the appropriate swfl.

You're just doing it wrong.

[M4bad]

Originally Posted by Almaretto

1. Make sure update VCM is unchecked in E-sys Settings
2. Connect to Car
3. Read FA
4. Change Typecode (in FA) to GTS variant
5. Activate FA
6. Hold Control and select modules you wish to code
7. Select Code

Thanks!

[Almaretto]

Originally Posted by M4bad

Thanks!

[kubax86]

Originally Posted by Robert0

Only FDL-Coding and choosing the right Swfl from Psdzdata full will give you a result

[kubax86]

Originally Posted by Robert0

I´m no professionell. Let it make from Kubax and ask me for problems

[Robert0]

All my posts and threads are deleted....NICE