10-19-2016, 03:47 AM | #1 |
BimmerPost Supporting Vendor
756
Rep 504
Posts |
CSF's "GAMEOVER" High Performance Heat Exchanger
Hello everyone,
CSF has joined the forums to spread awareness about our new line of high performance / race-spec line of coolers for the F8x M3/M4 platform. We'll be releasing 3 coolers at SEMA in two weeks! - 1st up for public release is our new: ”GAMEOVER" High Performance Heat Exchanger By this time, everyone has read the spiel on the benefits of a high performance heat exchanger for these vehicles so we'll just skip to presenting why ours is the best option available on the market. - Please see the bullet points (in our e-flyer above) as well as our comparison charts to other options on the market today. (zoomed below for easier review) We'll have 2 versions of this cooler available. STREET (presented in these charts) as well as a limited test-run of Race-Spec larger more hard-core units for dedicated race-cars. STREET
Race-Spec
* I know the questions will start coming on what exactly is required - I will put some detailed instructions on our race-spec version later this week Street version installed Before going any further, we feel it is important to state that CSF is the ONLY company that is the actual cooling system manufacturer of the full heat exchanger from the options that are currently available on the market today. Because of this fact, CSF possesses:
You can read more about our 4-generation company history on SPEEDHUNTERS WHAT IS B-TUBE TECHNOLOGY?? Short Answer:
Long Answer Unlike a regular oval shape "O" type radiator tube, CSF uses a specially engineered tube in a shape of a "B". These "B-tubes" are carefully formed and then brazed over the seam to seal. CSF is able to use thinner and lighter aluminum material (better cooling efficiency) because this design is actually stronger than normal "O" shape tubes that are welded. The design (inlet in the middle of tube that is seam brazed) increases the heat transfer surface area of the tube by approximately 15% over regular tubes. You get the efficiency of 2 smaller tubes vs. 1 large tube within the same space criteria. With "B-tubes" you are able to get "dual liquid laminar flow." The tubes are made from aircraft grade special clad aluminum and are intricately formed on our high precision 6-stage tube-forming mill. No other aftermarket radiator manufacturer uses this technology. This technology raises the bar and sets the standard for high performance radiator cores. HIGH PRECESION MULTI-LOUVERED 6.5mm FIN The fin height of the core directly effects:
The smaller the fin height the more dense the core is, and also the more surface area contact between the fins and tubes. More surface area contact means more heat rejection from the transfer of the heat out of the coolant and into the air that is passing through the core. Also the smaller the fin height the more tubes you can pack in the same size core. When it comes to thermal transfer, there has to be a harmonious balance between 3 major characteristics:
The OEM unit has a 1-row 27mm thick core with a 6.0mm fin height. This is a very efficient core. With CSF increasing the core thickness to a 2-row 42mm core, we opted to only increase the fin height slightly to 6.5mm. We tested this core configuration on our in-house wind-tunnel machine, and we found this to have negligible effects of the performance of the rest of the cooling system. Important Note: We're fortunate to be working with Yost Autosport on their race program as their cooling supplier. Because of this, we were able to have their entire cooling system out of the car for 2+ months to reverse engineer, inspect, and test against our high performance offerings. We sized our cooler to leave more space at the bottom of the cooling system to give best airflow to the DCT cooler as well as unimpeded exit airflow for the oil cooler that is placed perpendicular to the rest of the cooling system. TESTING & VALIDATION We're working with 2 respected BMW affiliates to help publish our testing data.
PRICE & AVAILABILITY This is the 1st forum that we've ever joined as we don't sell directly to the end consumer. We support the automotive distribution channel through our network of distributors and select direct-dealers (many of them who are forum sponsors). Not going to break any rules, but the price for our heat exchanger will be the same price as the most competitive offering on the market today. (i'll post in the vendor section later this week as well) Race-Spec - available now - 18 pieces left Street - Will start being available December 1st-15th. For all pre-orders, please contact our R&D partner / distributor/dealer - VF ENGINEERING. You can also PM us if you have any questions. If you'll be attending SEMA, please come by our booth in central hall (#21653) to check out all of our our new M3/M4 coolers on display and the debut of the new PSM Dynamic wide-body Yost Autosport M4 endurance race car Last edited by CSF Cooling; 10-19-2016 at 04:05 AM.. |
10-19-2016, 10:33 AM | #6 |
Colonel
749
Rep 2,108
Posts |
Sounds interesting...
So the street version requires no modifications what so ever and is truly a direct replacement of the OEM? I have to ask because other manufacturers have advertised their heat exchanger as a direct replacement, but then once you look at the installation manual you realize it requires some modification.
__________________
2015 BMW F80 M3: Tractive EDC Suspension / Dinan Anti-Roll Bars / GC Camber Plates / KMP Dual Diff Mount / Girodisc Rotors / GT4 Brake Cooling Kit / PTF Flash Tune / Eisenmann Downpipes / CSF Heat Exchanger / BMS Charge Pipes
2007 BMW E92 335i (SOLD): BMS JB4 / Quaife LSD / Riss Racing DPs / Helix Intercooler / BMS Intake / STETT Charge Pipe / Forge DVs |
Appreciate
0
|
10-19-2016, 12:24 PM | #8 |
BimmerPost Supporting Vendor
24171
Rep 190,750
Posts |
Looks good!!
Sub'd for test results
__________________
Check out our current sale by clicking on this link!
https://x-ph.com/sale/ Phone number 702-494-9435 |
Appreciate
0
|
10-19-2016, 01:23 PM | #9 | |
Major
1009
Rep 1,388
Posts |
Quote:
There is some minor trimming of the plastic ducting that feeds the air to the radiators ... and by minor, we're literally talking about a couple small scissor cuts to provide clearance between the larger heat exchanger and the x-brace. I'm certain that the install manual will be posted soon, and people will be impressed by the simplicity. |
|
Appreciate
0
|
10-19-2016, 01:41 PM | #10 | |
Major
1009
Rep 1,388
Posts |
Quote:
All three items will be on display at SEMA. We'll be announcing our pre-order schedule as soon as we have confident delivery dates for each item. |
|
Appreciate
2
apexit214.00 |
10-24-2016, 02:34 AM | #13 |
BimmerPost Supporting Vendor
756
Rep 504
Posts |
We're starting to ship "Race-Spec" versions of our heat exchangers to customers. We're also now working with Pure Turbos to get these heat exchangers, along with our other upcoming cooling upgrades, onto the most powerful cars in the industry, including their own shop M4 which will be getting our race-spec heat exchanger upgrade this week!
Picture below of an upgraded M4 that attended the top Speed Shit S3ctor event in California this weekend - installed by Autohaus Frankfurt in Murrieta, CA Stay Tuned! |
Appreciate
1
schnell1982345.00 |
10-26-2016, 02:51 PM | #14 |
Private
25
Rep 61
Posts
Drives: N54 + S55
Join Date: Jan 2015
Location: Houston
|
Very interested in results, sub'd
|
Appreciate
0
|
01-11-2017, 09:18 AM | #15 |
BimmerPost Supporting Vendor
756
Rep 504
Posts |
Our 45-row drop-in fit version is now available for sale. We have 50 units in stock.
No wait, and the best heat exchanger in terms of performance, finish, and fitment in stock - ready to ship - contact your CSF dealer/distributor today. |
Appreciate
0
|
01-11-2017, 10:47 AM | #16 | |
Captain
345
Rep 966
Posts |
Quote:
+1 for the guys at Autohaus Frankfurt They work on my cars. Great products CSF ! I have your cooling parts on my E46 M3 ! Love them !! |
|
Appreciate
1
CSF Cooling755.50 |
01-12-2017, 02:17 AM | #17 |
Private First Class
152
Rep 188
Posts |
What is the weight difference comparing to the stock unit?
__________________
"Learn the rules like a pro, so you can break them like an artist."
|
Appreciate
0
|
Post Reply |
Bookmarks |
Tags |
csf, heat exchanger, sema 2016 |
|
|