OLED Tail Lights for F80 M3

[wdskukm3]

I actually went back to my Pre LCI lights from the Bayoptiks FOLED. Fitment was ok but the lighting was a really bright deep red. I just didn't think the design fit the F80.

[s55jesus]

Originally Posted by Abdul

The F82 lights don't have this issue. The earlier batches of the F80 lights had this problem. Thanks.


Abdul

So the F80 OLED's no longer have this issue of it being super dim in direct sunlight?

[alicerink]

I installed mines from vland and in a month 1 lamp died

[Sky-watsher]

Originally Posted by Abdul

Just a quick update:

I have 40 plus sets in stock again. PM for a promo code and I'll get you sorted. I have extended the warranty on these lights to 3 years. Anything happens, I will replace it for free.

https://mpowermotorsports.org/produc...e-tail-lights/

On to ICON lights now. Wish me luck!

Hey Abdul,

Do you ship Worldwide ? if that's the case what are the shipping cost and does the coupon still apply here ?

Asking for my 2015 PRe-LCI F80

Thanks

[kk_alpine]

Anyone have the issue where the turn signals will work for the first few blinks and then get the error malfunction light? Sometimes on the left, sometimes right, sometimes both? BTW, this is a pre-lci F80

Would like to know if there is a solution, kind of tiring having that pop up all the time over the last week and a half and not having proper rear turn signals.

Input, advice would be super appreciated.

[F32 M Perf.]

Originally Posted by kk_alpine

Anyone have the issue where the turn signals will work for the first few blinks and then get the error malfunction light? Sometimes on the left, sometimes right, sometimes both? BTW, this is a pre-lci F80

Would like to know if there is a solution, kind of tiring having that pop up all the time over the last week and a half and not having proper rear turn signals.

Input, advice would be super appreciated.

I had this too on the right side (passenger) tails on my pre-LCI F32. I noticed that this happens with humid weather only and not all the time. Sometimes, I'd switch off the car and turn it back on the error would go away and the tails would work fine. Nonetheless, I wrote to VLAND from whom I got the lights through Amazon and they sent me an outer light replacement. I haven't installed it yet.

[kk_alpine]

Originally Posted by F32 M Perf.

I had this too on the right side (passenger) tails on my pre-LCI F32. I noticed that this happens with humid weather only and not all the time. Sometimes, I'd switch off the car and turn it back on the error would go away and the tails would work fine. Nonetheless, I wrote to VLAND from whom I got the lights through Amazon and they sent me an outer light replacement. I haven't installed it yet.

Yeah, if I turn off the car and back on again, the error goes away until the next time I use the signals.

Did you write to VLAND directly? Or did you go through Amazon to get the outers? Might have to do the same.

[F32 M Perf.]

Originally Posted by kk_alpine

Yeah, if I turn off the car and back on again, the error goes away until the next time I use the signals.

Did you write to VLAND directly? Or did you go through Amazon to get the outers? Might have to do the same.

Vland was the "seller" on Amazon, so I just contacted Vland through "contact seller".

[kk_alpine]

Originally Posted by F32 M Perf.

Vland was the "seller" on Amazon, so I just contacted Vland through "contact seller".

Awesome, just did that. Thanks!

[jmciver]

Originally Posted by kk_alpine

Anyone have the issue where the turn signals will work for the first few blinks and then get the error malfunction light? Sometimes on the left, sometimes right, sometimes both? BTW, this is a pre-lci F80

Would like to know if there is a solution, kind of tiring having that pop up all the time over the last week and a half and not having proper rear turn signals.

Input, advice would be super appreciated.

If the light still functions properly, you should be able to fix this random error notification with coding. Even though my car is a LCI (which came with LED tails from the factory), I still got an occasional tail light lamp error. To prevent errors for all BMW models, pre-LCI and LCI, VLAND adds resistors to make the car’s bulb voltage check circuit think everything is OK. Unfortunately, the resistors they use are not the best quality, thus they send an erroneous voltage signal to the bulb voltage check circuit occasionally, and the car thinks you have a bulb issue.

I coded my tails to LED using BimmerCode. Even though my car came with LED tails from the factory, some of the bulb parameters were not coded to LED. I coded everything to LED and no longer had any random tail light malfunction errors. I posted it somewhere in this thread, but I am too lazy to go find it…

[kk_alpine]

Originally Posted by jmciver

If the light still functions properly, you should be able to fix this random error notification with coding. Even though my car is a LCI (which came with LED tails from the factory), I still got an occasional tail light lamp error. To prevent errors for all BMW models, pre-LCI and LCI, VLAND adds resistors to make the car’s bulb voltage check circuit think everything is OK. Unfortunately, the resistors they use are not the best quality, thus they send an erroneous voltage signal to the bulb voltage check circuit occasionally, and the car thinks you have a bulb issue.

I coded my tails to LED using BimmerCode. Even though my car came with LED tails from the factory, some of the bulb parameters were not coded to LED. I coded everything to LED and no longer had any random tail light malfunction errors. I posted it somewhere in this thread, but I am too lazy to go find it…

I think I just found your post, haha. Will try the coding sometime this week or next once I get the time!

[SanchoDivine]

Originally Posted by Samf82m4

I've wanted to pull the trigger on some GTS tails for my F82 pre-lci for quite some time now. After seeing a lot of reviews regarding low brake and turn signal output, I'm going to hold off.

Has anyone addressed this issue yet? Is it really that bad?

The issue was the turn signals being dim in direct sunlight. The brake lights are pretty bright.

[mwalter14]

Originally Posted by Abdul

Just a quick update:

I have 40 plus sets in stock again. PM for a promo code and I'll get you sorted. I have extended the warranty on these lights to 3 years. Anything happens, I will replace it for free.

https://mpowermotorsports.org/produc...e-tail-lights/

On to ICON lights now. Wish me luck!

Pm'd!

[bigj505]

Originally Posted by Bavarian-Coding

nothing beats genuine OEM!

L

[F32 M Perf.]

For me, it wasn't just the error on the dash and Drive re the turn signal malfuction. When that was happening the turn signal would flash faster that usual and there would be either half or not at all turn signal blinking in the back.

Originally Posted by jmciver

If the light still functions properly, you should be able to fix this random error notification with coding. Even though my car is a LCI (which came with LED tails from the factory), I still got an occasional tail light lamp error. To prevent errors for all BMW models, pre-LCI and LCI, VLAND adds resistors to make the car’s bulb voltage check circuit think everything is OK. Unfortunately, the resistors they use are not the best quality, thus they send an erroneous voltage signal to the bulb voltage check circuit occasionally, and the car thinks you have a bulb issue.

I coded my tails to LED using BimmerCode. Even though my car came with LED tails from the factory, some of the bulb parameters were not coded to LED. I coded everything to LED and no longer had any random tail light malfunction errors. I posted it somewhere in this thread, but I am too lazy to go find it…

[F32 M Perf.]

Hey smart pants!! Nothing beats not spending 15,000 dollars for the oem that require harness and additional coding!! LMAO

Originally Posted by bigj505

L

[bigj505]

Originally Posted by F32 M Perf.

Hey smart pants!! Nothing beats not spending 15,000 dollars for the oem that require harness and additional coding!! LMAO

But this is the f80 version. Even 15k doesn't get you oems

[torvektheo]

I got a set for sale. I sold my F80 M3. I got version 2. PM me for info.

[Jim45678]

Anyone got such errors when starting engine?? all lights are working correctly but the message keep coming back from time to time?

[Jim45678]

Rectangle marked spot shall be also giving light when brake pedal is pushed, isn't it? It seems like I'm missing some wire connection. Can it cause the lighting error Im getting?

[petar7408]

does that rectangle spot work on the other side?

[Atlantis M3tallic]

Originally Posted by Jim45678

Rectangle marked spot shall be also giving light when brake pedal is pushed, isn't it? It seems like I'm missing some wire connection. Can it cause the lighting error Im getting?

Same thing happened to me but only on the passenger side. There is a 2pin harness (2 wires) that connects to the outer tail light. Mine disconnected, plugged it back in and it's working fine. I didn't have any errors just noticed it wasn't working.