01-09-2021, 08:34 PM | #1 |
Private
25
Rep 67
Posts
Drives: 2016 F80
Join Date: Jul 2007
Location: Cincinnati, OH
|
PDC not working and not sure where to look for the issue
I have a 2016 F80 with rear PDC only (no front) and all of a sudden PDC stopped working and I get an error message on the screen. I have done all I can think to do to diagnose the issue. First I tried WD40 on each sensor. I didn't think this would work but I thought I would give it a try. Then I tried running the codes with Bimmerlink. I get the following 8032D0, 8032D8, 8032E0 and 8032E8. All 4 errors say "Ultrasonic sensor front outside right, center right, center left and outside left; Line-interruption". All 4 errors say front PDC which is odd as I do not have front PDC, only rear. I then checked all 4 fuses for the PDC. All look good. Then I figured it must be a connection issue as I just had the back bumper repaired. PDC was working for a week after I got the car back from the body shop. I removed the bumper and all connections look good. I'm not sure where to look next. Any ideas? Certainly all 4 sensors did not go out at once. I am out of warranty and don't want to go to the dealer unless I have no other option.
__________________
2016 F80 Laguna Seca Blue/Carbon Structure, KW HAS Kit, Black Gills/Grills, AA Midpipe
Sold - 2011 E92 Alpine White/Fox Red ZCP, RPI Axle Back Exhaust, Black Gills/Grills, Key Hole Delete, Painted Reflectors, V-style Front Lip Sold - 2004 E46 Titanium Silver/Black, Borla Exhaust, Black Gills/Grills, CSL Trunk, VMR CSL-R wheels |
01-09-2021, 09:33 PM | #3 |
Private
25
Rep 67
Posts
Drives: 2016 F80
Join Date: Jul 2007
Location: Cincinnati, OH
|
Thanks but I tried that when I was checking the fuses.
__________________
2016 F80 Laguna Seca Blue/Carbon Structure, KW HAS Kit, Black Gills/Grills, AA Midpipe
Sold - 2011 E92 Alpine White/Fox Red ZCP, RPI Axle Back Exhaust, Black Gills/Grills, Key Hole Delete, Painted Reflectors, V-style Front Lip Sold - 2004 E46 Titanium Silver/Black, Borla Exhaust, Black Gills/Grills, CSL Trunk, VMR CSL-R wheels |
Appreciate
0
|
01-10-2021, 02:31 AM | #4 |
First Lieutenant
188
Rep 364
Posts
Drives: M2C X5M M4
Join Date: Jan 2020
Location: Southwest UK
|
I would think the pdc control unit has failed, it's a codeable part so if it is that you would either need software or to get it coded.
|
Appreciate
0
|
01-12-2021, 07:47 AM | #6 |
New Member
10
Rep 28
Posts |
I had this happen to me on my previous car. Found the PDC wiring loom to the control module had decided to fail unexpectedly. Luckily the loom was only for the rear half of the car so didn't have to remove much and the loom wasn't a bank breaker either
|
Appreciate
0
|
01-12-2021, 07:48 AM | #7 |
New Member
10
Rep 28
Posts |
|
Appreciate
0
|
06-04-2022, 09:41 AM | #8 |
Registered
0
Rep 1
Posts
Drives: 2015 bmw m4 --- 2019 bmw x3
Join Date: Jun 2022
Location: North Carolina
|
Found my issue, hope it helps
So i had the same issue. Removed the bumper and checked the connection, it was corroded inside so im going to have to cut that one off, and replace the connector. Moisture must've gotten in.
ig = M4NNY_GOT_IT |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|