Amber delete

[F80_BK]

Originally Posted by hC1001

I just started coding and this is the first istep version im coding with. I updated all the ECUs from F020_17_03_505 istep.

I've only touched HU_NBT2, and ASD modules and didnt run into any issues like i do with TMS ECUs. Maybe i should try esys v3.33...

Looks like my i-step is slightly older

[hC1001]

Originally Posted by F80_BK

Looks like my i-step is slightly older

Dont worry about looking at what istep you have. Probably better for someone else who is on a later istep version to confirm if they have worded folders or "." as well.

Thanks tho.

[omgf80]

Originally Posted by F80_BK

Yes. You have FLE instead of TMS. I mentioned this in my first reply for people with the newer FLE modules.


For FLE ECUs:

-To turn the side markers off, change LM_ID_LT04 and LM04_Name to F015Wert.

-To turn the side markers back on, change LM_ID_LT04 and LM04_Name back to F015Wert_SA552_SAE.

Ah missed that part. I didn't see "F015Wert" as an option within the "Front light Electronics Left/Right" but I did just change LM_ID_LT4 and LM04_Name to "00x0" which seemed to do the trick!

Thank you for the help!

[F80_BK]

Originally Posted by omgf80

Ah missed that part. I didn't see "F015Wert" as an option within the "Front light Electronics Left/Right" but I did just change LM_ID_LT4 and LM04_Name to "00x0" which seemed to do the trick!

Thank you for the help!

Glad it worked!

[EezyBeezy]

Originally Posted by omgf80

Ah missed that part. I didn't see "F015Wert" as an option within the "Front light Electronics Left/Right" but I did just change LM_ID_LT4 and LM04_Name to "00x0" which seemed to do the trick!

Thank you for the help!

Just did this on my '18 F80 through expert mode using Bimmercode and worked perfectly. Those (3) little amber LEDs just looked out of place.

For those who have "Front Light Electronics Left" and "Front Light Electronics Right" control units here is exactly what I did.

Front Light Electronics Left
- Navigate to Front Light Electronics Left
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Check & verify if value changes worked for the Left headlight. If no-go, revert back. If good, then proceed with the Front Light Electronics Right control unit.

Front Light Electronics Right
- Navigate to Front Light Electronics Right
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Enjoy!

Thanks all to previous posters for cluing me in.

[horsepower_and_hounds]

I wish I could get mine to work...... I was told by Alex that coded my car it could not be done on my 2015 cuz it had the files updated somewhere along the line

[hC1001]

Wanted to update my situation with the wierd folder names. In Esys 3.3.4, i used detect CAF for SWE and code on both TMS modules. After, i was able to see the correct folder names in Esys launcher pro 2.8.2+Esys 3.27 and successfully coded out the 3 amber LEDs using instructions in post 3.

Also, i found another method to disable the 3 amber LEDs, remove the corner light module from the headlight and disconnect the connector to the 3 amber LEDs. No coding necessary.

[alexhjs]

Originally Posted by EezyBeezy

Just did this on my '18 F80 through expert mode using Bimmercode and worked perfectly. Those (3) little amber LEDs just looked out of place.

For those who have "Front Light Electronics Left" and "Front Light Electronics Right" control units here is exactly what I did.

Front Light Electronics Left
- Navigate to Front Light Electronics Left
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Check & verify if value changes worked for the Left headlight. If no-go, revert back. If good, then proceed with the Front Light Electronics Right control unit.

Front Light Electronics Right
- Navigate to Front Light Electronics Right
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Enjoy!

Thanks all to previous posters for cluing me in.

I just wanted to chime in and let you guys know that this exact method worked on my '18 F85 X5M. The 2018s have the iDrive updated and BimmerCode did not have easy menus enabled to code off the ambers but this code shared via expert mode worked perfectly. Thanks again!

[EezyBeezy]

Originally Posted by alexhjs

I just wanted to chime in and let you guys know that this exact method worked on my '18 F85 X5M. The 2018s have the iDrive updated and BimmerCode did not have easy menus enabled to code off the ambers but this code shared via expert mode worked perfectly. Thanks again!

Cheers!

[wknd_M]

Originally Posted by alexhjs

I just wanted to chime in and let you guys know that this exact method worked on my '18 F85 X5M. The 2018s have the iDrive updated and BimmerCode did not have easy menus enabled to code off the ambers but this code shared via expert mode worked perfectly. Thanks again!

I will definitely give this a try, the ambers are an eye sore on my LCI

[KACHM3]

just wanted to say..it works…thank you

[wknd_M]

Originally Posted by EezyBeezy

Just did this on my '18 F80 through expert mode using Bimmercode and worked perfectly. Those (3) little amber LEDs just looked out of place.

For those who have "Front Light Electronics Left" and "Front Light Electronics Right" control units here is exactly what I did.

Front Light Electronics Left
- Navigate to Front Light Electronics Left
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Check & verify if value changes worked for the Left headlight. If no-go, revert back. If good, then proceed with the Front Light Electronics Right control unit.

Front Light Electronics Right
- Navigate to Front Light Electronics Right
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Enjoy!

Thanks all to previous posters for cluing me in.

It worked! Did this today on the car, thanks for sharing

[Mandi90TT]

Saw this thread pop up and thought it was another Heard/Depp discussion...

[2Times]

Originally Posted by EezyBeezy

Just did this on my '18 F80 through expert mode using Bimmercode and worked perfectly. Those (3) little amber LEDs just looked out of place.

For those who have "Front Light Electronics Left" and "Front Light Electronics Right" control units here is exactly what I did.

Front Light Electronics Left
- Navigate to Front Light Electronics Left
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Check & verify if value changes worked for the Left headlight. If no-go, revert back. If good, then proceed with the Front Light Electronics Right control unit.

Front Light Electronics Right
- Navigate to Front Light Electronics Right
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Enjoy!

Thanks all to previous posters for cluing me in.

This worked perfect on my 2020 F83. Super fast and easy the way you laid it out. Thank you. Going to try the same thing on my X3M later.

[EezyBeezy]

Originally Posted by 2Times

This worked perfect on my 2020 F83. Super fast and easy the way you laid it out. Thank you. Going to try the same thing on my X3M later.

Glad to hear. Cheers!

[Sloblk8]

Originally Posted by EezyBeezy

Just did this on my '18 F80 through expert mode using Bimmercode and worked perfectly. Those (3) little amber LEDs just looked out of place.

For those who have "Front Light Electronics Left" and "Front Light Electronics Right" control units here is exactly what I did.

Front Light Electronics Left
- Navigate to Front Light Electronics Left
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Check & verify if value changes worked for the Left headlight. If no-go, revert back. If good, then proceed with the Front Light Electronics Right control unit.

Front Light Electronics Right
- Navigate to Front Light Electronics Right
- Click on Expert mode
- Click on 3006 LED1
- Click on LM_ID_LT4
- Change to 02_VALUE / 0x00
- Go back to the 3006 LED1 page
- Click on LM04_NAME
- Change to 02_VALUE / 0x00
- Back on 3006 LED1 page and click code

Enjoy!

Thanks all to previous posters for cluing me in.

I know this is an old thread but what about people that don't have "Front Light Electronics Left" or "Front Light Electronics Right" options on the Bimmercode main screen?

The lighting stuff is in the Front Electronic Module and I don't see 3006LED1 at all in the expert section. There is a cornering lights deactivation but it's already showing active . Thanks for the help.

[kubax86]

Originally Posted by Sloblk8

I know this is an old thread but what about people that don't have "Front Light Electronics Left" or "Front Light Electronics Right" options on the Bimmercode main screen?

The lighting stuff is in the Front Electronic Module and I don't see 3006LED1 at all in the expert section. There is a cornering lights deactivation but it's already showing active . Thanks for the help.

All depends on current lights

[Sloblk8]

Originally Posted by kubax86

All depends on current lights

It's an 18 M3 comp so the LCI headlights I assume. I know it's small but the headlights like in my avatar pic.

[kubax86]

Originally Posted by Sloblk8

It's an 18 M3 comp so the LCI headlights I assume. I know it's small but the headlights like in my avatar pic.

FLE modules then.

[Sloblk8]

Originally Posted by kubax86

FLE modules then.

Thanks man, I'm gonna hook it up when I get off of work and look for that module. Thanks again for your time.

[vermethlln]

Originally Posted by 2Times

This worked perfect on my 2020 F83. Super fast and easy the way you laid it out. Thank you. Going to try the same thing on my X3M later.

Will this work on my G01 2019 X3 as well? I want to turn off the amber lights for the EU inspection. Thanks in advance

[kubax86]

Originally Posted by vermethlln

Will this work on my G01 2019 X3 as well? I want to turn off the amber lights for the EU inspection. Thanks in advance

Different on G01. Can help if needed.

https://bimmer-remote.com/products/b...f395e811&_ss=r