|
Post Reply |
|
Thread Tools | Search this Thread |
06-19-2021, 10:24 AM | #1 |
Second Lieutenant
145
Rep 230
Posts |
Several Pressure sensor errors after crank hub replacement
hi guys, getting some errors after crank hub replacement. timing chain, oil pump chain and rails were also replaced.
car cranks very late, and sometimes run at second try. currently in limp mode. errors : 10442 : Absolute pressure sensor, intake pipe, electrical : short circuit to ground 119001 - Rail pressure sensor, electrical : Short circuit to B+ 199202- fuel low-pressure sensor, electrical : Short circuit to ground. 120408 - Charging pressure control : switch-off as consequential reaction 1C3002 - Engine oil pressure sensor, electrical : Short circuit to ground 1C3102 - Engine-oil pressure sensor, plasubility : Pressure too high before engine start 1C3101 - Engine-oil pressure sensor, plausbility : Pressure too low before engine start 1F1A91 - DME , monitoring, 5V sensor supply 2: Voltage outside valid range. sometimes most of the codes disappear and these stays on. 199202- fuel low-pressure sensor, electrical : Short circuit to ground. 1F1A91 - DME , monitoring, 5V sensor supply 2: Voltage outside valid range. and sometimes 1C3101 and 1C3102 disappears as well. what might be the thinks to check? already plugged out-in however no difference. |
06-21-2021, 01:52 PM | #3 | |
Private
26
Rep 52
Posts |
Quote:
Have you spoken to the guys who did the work? Since they are all related to the work you had done, I'd guess they were installed incorrectly. I'd start there for sure. |
|
Appreciate
0
|
06-21-2021, 01:58 PM | #4 |
Lieutenant
248
Rep 471
Posts |
I would check the connector for the fuel pressure sensor on the back end of the fuel rail (the firewall end) and make sure it's plugged-in all the way.
Don't know where the oil pressure sensor is on these, but I would find that and check that connector, too. After that, absolutely take it back to whoever did the work and tell them to get it straight. Last edited by 1000hp; 06-21-2021 at 02:09 PM.. |
Appreciate
0
|
08-11-2021, 10:27 AM | #5 |
Registered
2
Rep 2
Posts |
hello im waiting for updates on this matter, i have the same problem after i replaced a crank hub on bmw m4 and my mechanic reversed the dme plugs in the wrong socket, now the car has several error codes, please any idea or solution would be great
|
Appreciate
1
mord49.00 |
08-11-2021, 02:52 PM | #7 |
Colonel
1973
Rep 2,711
Posts |
Common installation error is mixing up the two camshaft gears (#4 and #5) in the following diagram: https://www.realoem.com/bmw/enUS/sho...diagId=11_5626
This will throw a bunch of random unrelated trouble codes. |
Appreciate
2
TopJimmy5460.00 theweebabySeamus376.00 |
08-11-2021, 06:35 PM | #8 |
Lieutenant
116
Rep 482
Posts |
Better question ... who / what shop did the install?
|
Appreciate
1
fiveohwblow3633.00 |
09-04-2021, 02:10 PM | #11 |
Lieutenant
191
Rep 493
Posts |
|
Appreciate
0
|
04-17-2023, 08:43 AM | #14 |
Second Lieutenant
145
Rep 230
Posts |
probably one around the engine sits. check all of them in detail you will probably notice. on the other hand it might be something else
|
Appreciate
0
|
06-11-2023, 11:09 PM | #15 |
Private
3
Rep 55
Posts |
|
Appreciate
0
|
08-16-2023, 04:02 PM | #16 |
Registered
0
Rep 1
Posts |
Any idea what wire got pinched???? im dealing with the same after customer had crank hub done at a different shop literally the exact same codes...they decided to make it my problem Last edited by denverfan9; 08-16-2023 at 04:08 PM.. |
Appreciate
0
|
08-16-2023, 10:03 PM | #17 |
New Member
7
Rep 7
Posts |
Hey guys any updates on these random codes after crank hub job. Having same issue. I speculated about that junction box on driver side under dme plugs
__________________
If it work then it works
|
Appreciate
0
|
09-22-2023, 09:59 PM | #19 |
Major
664
Rep 1,074
Posts |
OP has a case of, if its my problem everyone better help me, but once it becomes your problem i don't help you. lol
__________________
Instagram: M2_Medusa
|
Appreciate
0
|
09-22-2023, 11:16 PM | #20 |
First Lieutenant
176
Rep 301
Posts
Drives: BMW M3
Join Date: Mar 2019
Location: CA6
|
I had hpfp codes when I did my ch. I cleared the codes and they never came backk
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|