|
Post Reply |
|
Thread Tools | Search this Thread |
09-26-2013, 09:37 AM | #45 | |
Major General
![]() ![]() ![]() 3494
Rep 9,708
Posts |
Quote:
![]() |
|
Appreciate
0
|
09-26-2013, 11:28 AM | #46 | |
Captain
![]() ![]() ![]() ![]() ![]() 345
Rep 686
Posts |
Quote:
|
|
Appreciate
0
|
09-26-2013, 01:21 PM | #48 |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
The characteristics of an engine can certainly be altered by over and under square designs but the differences between them are dwarfed by the effect of turbo charging.
Using a caliper and paper print out of the new block (ugh, I am really that bad... although I could have also gone the Photoshop route) I calculate an 8.0 mm cylinder wall thickness for the S55 meaning the bore spacing is 97.6 mm. If they wanted an even mm bore spacing I'd then guess 98 mm. This makes the new block a full 33 mm (1.3 inches) longer from 1st to last bore. Either way, I was already firmly convinced that a 1.4 mm cylinder wall spacing was completely unfeasible from a structural and thermal fatigue point of view. I posted that there was a new bore spacing at least a day or two ago here buried in one of the long discussions... It is a new block and thus new head as well. It is based highly on the design of the N55 block but indeed has a different bore spacing.
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
Appreciate
0
|
09-26-2013, 01:37 PM | #49 |
Moderator
![]() 7543
Rep 19,368
Posts |
Swamp, I agree that the S55 block pictures essentially rule out a bore increase from the 84mm of the N55 if the block were using 91mm center like that motor.
Call me stubborn, but I am still skeptical that the claimed bore and stroke (and resulting new I6 architecture) are correct. I am not saying anyone is lying, just waiting for more confirmation. Also, as I said earlier, 98mm would be the only thing that makes sense given the N74 and existing tooling. If this is all true, prepare for an explosion in big bore and stroker kits from the aftermarket. And for those building classic BMWs with custom power trains, reliable 500hp should be possible N/A from this block. |
Appreciate
0
|
09-26-2013, 03:01 PM | #50 |
Major General
![]() ![]() ![]() 1727
Rep 5,110
Posts |
If this is correct, and if it has a 89,6mm bore then there has to be a larger bore spacing than 91mm.
Do you realize how much that affects change in tooling at the engine plant? Longer between crank main bearings, longer between cylinder bores and less space at each end if engine length is the same. Not to mention cyl head tooling. Again if the info is correct, BMW M must have seen a MAJOR benefit of going this route. Possibly the S55 is the base for a long line of future M engines with larger volume (longer stroke) and therefore makes it economically feasible to develop such a major change from the N55? But, doing a rough measurement of the N55 block picture, I get a bore spacing of 94mm, leaving a wall thickness of 4,4mm between cylinders with a 89,6mm bore... Where do we have the 91mm bore spacing from? (Keep in mind that my N55 measurements were very rough and I am open to being mistaken here...) (Doing a measurement on a picture of the N53 comes up with around 93mm bore spacing, but a very small measurement error at that scale makes a huge difference) Last edited by Boss330; 09-26-2013 at 03:37 PM.. |
Appreciate
0
|
09-26-2013, 03:04 PM | #51 | |
Lieutenant
![]() ![]() ![]() 37
Rep 513
Posts |
Quote:
![]() |
|
Appreciate
0
|
09-26-2013, 03:19 PM | #52 |
Major General
![]() ![]() ![]() 3494
Rep 9,708
Posts |
|
Appreciate
0
|
09-26-2013, 03:27 PM | #53 |
Lieutenant
![]() ![]() ![]() 37
Rep 513
Posts |
|
Appreciate
0
|
09-26-2013, 03:27 PM | #54 |
Second Lieutenant
![]() ![]() 16
Rep 277
Posts
Drives: 2014 M6 Gran Coupe
Join Date: Aug 2013
Location: The Southwest
|
Amazing how thin the cylinder walls are, between cylinders. I'm sure some magical engineering was done to prevent issues with heat and blown head gaskets. Looks like a groove was added to help keep the gasket in place.
__________________
2014 M6 Gran Coupe-Alpine White/Blk
2015 740i Sapphire Blk/Blk 2018 Tahoe RST 6.2 2019 Porsche 911 Turbo 991.2 ![]() Last edited by RiverRunner; 09-26-2013 at 05:25 PM.. |
Appreciate
0
|
09-26-2013, 03:29 PM | #55 |
Lieutenant
![]() ![]() ![]() 37
Rep 513
Posts |
|
Appreciate
0
|
09-26-2013, 03:38 PM | #56 | |
Major General
![]() ![]() ![]() 1727
Rep 5,110
Posts |
Quote:
And in that direction (between cylinders) it's mostly combustion pressures that affect the cylinder walls. Towards the outside the cylinder walls are thicker as that part has to deal with the forces applied on the piston via the crank rod during the rotation of the crankshaft. Those forces act against the cylinder wall since the crank rod during large parts of the rotation is at an angle against the cylinder wall. |
|
Appreciate
0
|
09-26-2013, 03:45 PM | #57 |
Major
![]() 196
Rep 1,248
Posts |
Yup, if I remember correctly the same is true of the walls on Merc's recent 5.5 bi-turbo when compared to BMWs 4.4 V8. Big capacity doesn't always mean bigger aftermarket gains on FI engines if initial capacity was gained through it being bored out, with exceptions and other factors involved of course.
|
Appreciate
0
|
09-26-2013, 03:53 PM | #58 |
Major General
![]() ![]() ![]() 1727
Rep 5,110
Posts |
The great thing with a large bore/short stroke engine is that it's possible for BMW M and the tuners to develop "stroker kits".
With a 85mm stroke this engine gets 3219cc With a 88mm stroke this engine gets 3329cc With a 89,6mm stroke this engine gets 3390cc Last edited by Boss330; 09-27-2013 at 07:30 AM.. |
Appreciate
0
|
09-26-2013, 03:55 PM | #59 | |
Major General
![]() ![]() ![]() 1727
Rep 5,110
Posts |
Quote:
Where do we have the 91mm bore spacing info from? Is it a verified measurement or just what everyone believes? |
|
Appreciate
0
|
09-26-2013, 04:17 PM | #60 |
Major General
![]() ![]() ![]() 3494
Rep 9,708
Posts |
We'll see. I speculate on a 4 pot as it's direct rival, the AMG CLA is a 4 pot. Also I can't see BMW stealing M3/4 customers with a lower cost 'mini me'.
|
Appreciate
0
|
09-26-2013, 04:30 PM | #61 | |
Lieutenant
![]() ![]() ![]() 37
Rep 513
Posts |
Quote:
On the one hand, the M135i is a straight 6 and I have heard nothing saying it will ever be anything but a straight 6. On the other, if BMW does include a straight 6 in the M2, they are going to be doing EXACTLY what they did with the 1M, the 335i and the M3. I can't imagine BMW wanting to take market share from the M3/M4 with the M2 but, they did it with the 1M and the 335i by including potent powerplants in both of their lesser offerings. They did it twice, after all. The fact that the M3/M4 has 450 hp leaves a lot of room for a 3000 pound, 350hp 2 series coupe but, will they use a straight 6?! An N20 derived 4 cylinder S series motor but, I hope to god that doesnt happen. |
|
Appreciate
0
|
09-26-2013, 04:32 PM | #62 | |
Lieutenant
![]() ![]() ![]() 37
Rep 513
Posts |
Quote:
|
|
Appreciate
0
|
09-26-2013, 04:48 PM | #63 |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
I got that number from one of the moderators here and it was publicly posted. I have not independently verified that number myself.
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
Appreciate
0
|
09-26-2013, 05:31 PM | #64 |
Second Lieutenant
![]() ![]() 16
Rep 277
Posts
Drives: 2014 M6 Gran Coupe
Join Date: Aug 2013
Location: The Southwest
|
Siamese cylinders, is what they were called when GM built the 400cid small block V8. That was 40 years ago, you couldn't go too far in increasing cylinder pressures or you'd blow a head gasket.
__________________
2014 M6 Gran Coupe-Alpine White/Blk
2015 740i Sapphire Blk/Blk 2018 Tahoe RST 6.2 2019 Porsche 911 Turbo 991.2 ![]() |
Appreciate
0
|
09-26-2013, 06:37 PM | #65 | |
Moderator
![]() 7543
Rep 19,368
Posts |
Quote:
Did you try an internet search? I will spend a few minutes and see what comes up. I am thinking of two particular S54 discussions that went into gross details including deck height, rod length, compression height, etc. |
|
Appreciate
0
|
09-26-2013, 06:42 PM | #66 |
Moderator
![]() 7543
Rep 19,368
Posts |
Using S62 bore (94mm) and S54 stroke (91mm), you get 3.8L. Both of these dimensions should be cake for this block if it is 98mm which matches BMW V8s and V12s from N73 onward (prior V12s shared the 91mm center bore of the I6 - they increased it to accommodate the Rolls displacement).
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|