eBay product ratings thread

[Poiseuille]

Originally Posted by boss2k

emailed the eurokingdom and they mention the holes are due to the spoiler being hung for UV clear coat spray

^^^ this makes sense

[smithf80]

Originally Posted by mindspin311

Bought this Lightweight lip replica, will report back.

https://www.ebay.com/itm/GLOSSY-BLAC...53.m2749.l2649

Did you get this yet? I've been looking at the same thing.

[mindspin311]

Originally Posted by smithf80

Did you get this yet? I've been looking at the same thing.

I have it. Have not had the opportunity to install yet. Looks good from what I can tell. Came with a bunch of hardware. It's not 100% flat when just laying on the floor, but that obviously might change once mounted to the car. I will do my best to take pictures of it during install.

[smithf80]

Originally Posted by mindspin311

I have it. Have not had the opportunity to install yet. Looks good from what I can tell. Came with a bunch of hardware. It's not 100% flat when just laying on the floor, but that obviously might change once mounted to the car. I will do my best to take pictures of it during install.

Thank you! Looking forward to hearing your thoughts once it's on.

[hatepotholez]

anyone get a CS carbon fiber front lip with good fitment?

[chujk1985]

I got the CF splitters from bulbxpert on eBay. Can I fit a Lightweight front lip on as well?

[mindspin311]

Originally Posted by chujk1985

I got the CF splitters from bulbxpert on eBay. Can I fit a Lightweight front lip on as well?

Im planning on doing this setup. Though I wont have results till after the new year.

[chujk1985]

Originally Posted by mindspin311

Im planning on doing this setup. Though I wont have results till after the new year.

In general, do you know if the cf splitters fit with the Lightweight lip?

[White340]

Can anyone recommend a rear diffuser (OEM style) and full front splitter (also OEM style)?

[jpm804]

If anyone was waiting:

eBay Coupon 15% off (max $100) ends at 6pm PST 12/18 - POPUPSAVINGS

[Sir Loin]

Originally Posted by gman_newyork

I purchased this. Fitment is 10, finish 10. Half the price of the one you quoted plus it is meant for M3 as M4 trunk is different.

https://www.ebay.com/itm/For-BMW-F30...fca8%7Ciid%3A1

Originally Posted by jpm804

If anyone was waiting:

eBay Coupon 15% off (max $100) ends at 6pm PST 12/18 - POPUPSAVINGS

Thanks for the ebay coupon jpm804 .

The link gman_newyork linked is no longer available. But I found the same part from the same seller. $124.95 shipped with coupon applied.

https://www.ebay.com/itm/112257880721

[Rockshaker]

Originally Posted by wolfgangvh

Bought the CF Mirror Replacements and the CS Style Spoiler from bulbexpert Monday and received today. Overall, very happy with the purchase.

Packaging: Extremely well-packed, multiple layers of bubble wrap and the items themselves were in a soft anti-scratch material bag. The box for the spoiler had two very hard cardboard edges to prevent any bending whatsoever. They obviously put time and thought into packing these.

Mirrors Replacements $229.99, Free Shipping https://rover.ebay.com/rover/0/0/0?m...2F202084492003

Quality: 9/10. No bunching in the weave...a very slight "haziness" in one spot if you look from the right angle...I'm being critical here. The clips are very sturdy compared to OEM. They are a very hard plastic.

Fitment: 9/10. I had ZERO issues getting these on the car. Installed in 20 mins max including time to remove old mirrors. The corner is not "perfect" as others have noted but by no means would this stop me from buying them again. Unless you are specifically looking for this then there is no way anyone will ever notice this. The three clips at the top do not align with the OEM mirror cover which concerned me at first but did not affect me snapping them into place.

CS Style Spoiler $156.99, Free Shipping
https://rover.ebay.com/rover/0/0/0?m...2F202382606948

Quality: 7/10. Random two small holes on the bottom. No idea why. I have a scratch on mine ~1in long on the top right of the spoiler...not very noticeable but it's there...I could be picky and ask for a replacement but I can buff this out. Few very light scratches in the clearcoat that you can only see when the light hits it at the right angle. Weave is OK...no major issues.

Fitment: 7/10. Bottom line...it will fit. The outer edges are not perfectly seated if you use one layer of tape. The middle will adhere very well to the trunk but the edges won't. Solution...use more tape. It does extend the full length of the trunk, curvature is pretty good too.

Will post pics later.

I purchased this same spoiler and installed it today. Fitment is good and it extends really close to the edge of the trunk. I got a little excited when I finished removing the OEM spoiler and tape in record time thanks to the tip on using the Adhesive Eraser Wheel (the install took about 45 minutes) and position spoiler a little too far to the right so my gaps are not equal. Other than that it went pretty smooth.

[nano10]

https://www.ebay.com/itm/Fits-15-18-...m3+side+skirts

Want to get these side skirts similar to OEM style. Seller is based out of California. Anyone Ave any experience?

[LOW4LYF]

Originally Posted by nano10

https://www.ebay.com/itm/Fits-15-18-...m3+side+skirts

Want to get these side skirts similar to OEM style. Seller is based out of California. Anyone Ave any experience?

How they can fit F80 and F82, F83? Be carful...

[Spoolin Montego]

Should have a follow up thread in 6-12 months once these people see parts that look good initially start falling apart due to inferior resins and clears used. Guarantee all the cf mirrors don't last past 6 month part. Plastic+cf ALWAYS degraded pretty quickly

[e85m4]

fuckk i missed that 15% coupon

[Sir Loin]

Originally Posted by e85m4

fuckk i missed that 15% coupon

ebay has been having these coupons every month toward the end of the month. Just wait a few weeks. It will come back.

[e85m4]

Originally Posted by Sir Loin

ebay has been having these coupons every month toward the end of the month. Just wait a few weeks. It will come back.

how can i get email notifications for these coupons?

[DataNerd]

Originally Posted by Rockshaker

I purchased this same spoiler and installed it today. Fitment is good and it extends really close to the edge of the trunk. I got a little excited when I finished removing the OEM spoiler and tape in record time thanks to the tip on using the Adhesive Eraser Wheel (the install took about 45 minutes) and position spoiler a little too far to the right so my gaps are not equal. Other than that it went pretty smooth.

That looks good! I don't think it's noticeable being a bit closer to one side over the other.

I just bought the same CS spoiler from bulbxpert. Did you have to use more than a single layer of double sided tape?

Thanks!

[gman_newyork]

Originally Posted by DataNerd

That looks good! I don't think it's noticeable being a bit closer to one side over the other.

I just bought the same CS spoiler from bulbxpert. Did you have to use more than a single layer of double sided tape?

Thanks!

I have the same spoiler from the same seller. I ran 2 strips along the edges (full length) and in the middle I had enough room to add a 3rd strip. Rock solid mount.

[Rockshaker]

Originally Posted by DataNerd

That looks good! I don't think it's noticeable being a bit closer to one side over the other.

I just bought the same CS spoiler from bulbxpert. Did you have to use more than a single layer of double sided tape?

Thanks!

Yes, I used two strips of tape to ensure it adhered to the trunk.

[mindspin311]

Originally Posted by Rockshaker

I purchased this same spoiler and installed it today. Fitment is good and it extends really close to the edge of the trunk. I got a little excited when I finished removing the OEM spoiler and tape in record time thanks to the tip on using the Adhesive Eraser Wheel (the install took about 45 minutes) and position spoiler a little too far to the right so my gaps are not equal. Other than that it went pretty smooth.

How did the underside of yours look? Mine had a few rough areas. The front edge of the spoiler had a lip in some areas that I knew would not let it sit flush. I went ahead and sanded the areas smooth. Still need to install.