04-05-2020, 10:15 PM | #1 |
SCHNELL
224
Rep 835
Posts |
Anyone fitted 265 35 20 fronts?
I'm keen on trying Cup2 R on the fronts. Anyone fitted up 265 35 20 without rubbing? Standard height ZCP on 666M.
|
04-22-2020, 07:45 AM | #3 |
Major General
5450
Rep 5,139
Posts |
It's not your exact answer since I run 19s but you can check comparison sizes. I've got a 275/35/19 Conti 5P up front on a 9.5 BBS. Never rubs. I corner aggressive. 295/3019 in rear. ET is 25F 35R. Stock springs.
Your 265 is made for a 9.5 but a front 666 wheel is 9.0 I think.
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
0
|
04-22-2020, 11:39 AM | #4 |
Captain
159
Rep 841
Posts |
answer
IME; no Michelin Cup 2 in that size is not going to work because it is as wide as a regular Star Michelin PSS 285. You car run 265-35 PSS Star with no problem, maybe just a little trim to the plastic inner fender.
|
Appreciate
0
|
04-22-2020, 07:58 PM | #5 |
Major General
5450
Rep 5,139
Posts |
I just ran your numbers.
The MPSC2 265/35ZR20 specs are: 9.5in rim (9-10.5in) 10.7 section 27.3 diameter The Conti5P 275/35ZR19 that I run up front: 9.5in rim (9-11in) 10.9 section 26.6 diameter The section width on my 275 is wider than your 265, so it won't rub suspension or wheel lip. The wheel height (diameter) on your 265 is 0.7in taller than me, and I can fit hands all around wheel gaps. Yours will fit. Look at the wheel gap left on this 275 front on a 9.5 BBS CI-R. I still need to install my Eibach V1 kit.
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
Appreciate
0
|
04-23-2020, 12:58 AM | #6 | |
Brigadier General
2162
Rep 4,106
Posts |
Quote:
A 265/35 20 will not fit without rubbing the inner fender! That's a 255/35 PSS Last edited by LOW4LYF; 04-23-2020 at 01:15 AM.. |
|
Appreciate
0
|
04-23-2020, 07:57 AM | #7 | ||
Major General
5450
Rep 5,139
Posts |
Quote:
I pulled the numbers straight off TireRack for MPS4S and Conti5P. Are you ZCP on stock springs like OP asks? Your pic looks lowered. -TJ
__________________
'18 F80 Base 6MT | '19 F82 Exec DCT | '18 F82 Comp Exec DCT | '23 G80cx
|
||
Appreciate
0
|
04-23-2020, 08:30 AM | #8 | |
Brigadier General
2162
Rep 4,106
Posts |
Quote:
You need to modify the inner fender in any case. |
|
Appreciate
0
|
11-19-2022, 12:35 PM | #9 |
Enlisted Member
9
Rep 43
Posts |
I have 265 35 20 on my stock suspension M4. Tires are Pirelli Pzero's on BBS FI 9.5 in wide wheels ET 26 I get fender liner rubbing turning occasionally.
|
Appreciate
0
|
01-25-2023, 07:42 AM | #10 |
Major
881
Rep 1,044
Posts
Drives: 2018 M4 Competition
Join Date: Mar 2018
Location: Chino Hills, California
|
Reviving this because I am wondering if it'll fit on my F82. Just noticed my near 85% thread left front tires have the wires on the inside. My toe must be off because camber is at stock spec. I have Michelin Pilot Sport 4S 275x30x20s in the front (zero rub) but I can get a killer deal for 265x35x20s.
The sizing specs I got from TireRack are: Michelin PS4S 275x30x20: Section Width @ 10.9 / Tread Width @ 9.8 / Overall Diameter @ 26.5 Michelin PS4S 265x35x20: Section Width @ 10.7 / Tread Width @ 9.6 / Overall Diameter @ 27.3 The overall diameter at .8" taller is a bit of a chunk but I don't have my front slammed either and definitely have .8" to give so I am curious if anyone out there has done this without issues on a 20" wheel.
__________________
Instagram: Slaughter.Mode
|
Appreciate
0
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|