|
Post Reply |
|
Thread Tools | Search this Thread |
06-04-2013, 05:41 AM | #67 |
Colonel
![]() ![]() 1125
Rep 2,564
Posts |
For the people arguing over the trap speeds - these are theoretical calculations but are fun nonetheless. I assume it has to also guess at the torque curves which adds to the potential inaccuracy. Should be interesting to compare real world results to these once real dynos are available. One place I think the theoretical calcs are off is the 5-60 runs. In the calculations it shows all 3 cars with a lower 5-60 than their respective 0-60. Mid 3's 5-60 is not going to happen.
|
Appreciate
0
|
06-04-2013, 10:14 AM | #68 | |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
Quote:
When to shift is quite simple, it is not about average power nor about torque, torque is irrelevant. One shifts where the accelerative force is higher in the next gear than if the shift was not made. In other words if lines on the force vs. speed in each gear cross that shift should be made at the vehicle speed (can back calculate rpm) where they cross. Simple.
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
|
Appreciate
0
|
06-04-2013, 10:38 AM | #69 | |
Lieutenant Colonel
![]() 290
Rep 1,577
Posts |
Thanks for the data swamp2, I really hope we can revisit this thread when the first car hits the dyno to see just how close you were to the real thing.
Quote:
6.9 seconds http://fastestlaps.com/cars/lamborgh...o_lp560-4.html Further proof your number may be incorrect is that the GTR 530hp/3900lbs 0-100mph in 7.4 seconds http://www.motortrend.com/roadtests/...t/viewall.html |
|
Appreciate
0
|
06-04-2013, 11:36 AM | #70 | |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
Quote:
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
|
Appreciate
0
|
06-04-2013, 12:56 PM | #71 | |
First Lieutenant
![]() ![]() 125
Rep 353
Posts |
Quote:
Oh really?? Thanks bud! That takes care of it all. ![]() ![]() Type in "lamborghini lp560-4 0-160 seconds" into google and see the times you get on the first couple of pages. Hint: They average out close to 8. Finding the fastest time on a press car isn't called 'proof', it just means you might be naive. ![]() |
|
Appreciate
0
|
06-04-2013, 01:01 PM | #72 | |
General
![]() ![]() ![]() ![]() ![]() 21156
Rep 20,745
Posts
Drives: 2021 911 turbo
Join Date: Jan 2012
Location: Montreal
|
Quote:
The only difference between propulsive force and wheel torque is the wheel radius (this is pretty much a constant on a street cars, maybe not on a top fuel dragster though ![]() You will find that when the force lines of two gears cross, the power generated in the lower gear is equal to the power generated at the higher gear at that speed. Thus maximizing average power. Last edited by CanAutM3; 06-04-2013 at 07:14 PM.. |
|
Appreciate
0
|
06-04-2013, 01:36 PM | #73 |
BMW Fan
![]() 463
Rep 728
Posts |
If BMW gets down to 3450 I'll be extremely impressed. The C7 Corvette has an aluminum chassis and they are barely squeaking below 3300lbs(3298) for the base model. A Z51 with the track stuff will probably add about 50-75 pounds to that.
|
Appreciate
0
|
06-04-2013, 02:04 PM | #74 |
Major General
![]() ![]() 5494
Rep 7,060
Posts |
Theory aside, in daily driving I will see little to no incentive to take this type of engine to the redline. Keeping it at full boil in the midrange will be more rewarding than extending it to a flat rpm peak. That you save both some fuel and engine component life doesn't hurt either. The S65 is such a savage towards the peak in both symphony and power that you run it up there all day long, or as often as you can. I think no matter how we dice it, there will be a difference in how we enjoy these cars unless BMW pull another rabbit out of the hat. I will not bet against them even if I chalk it down as unlikely.
|
Appreciate
0
|
06-04-2013, 02:31 PM | #76 | |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
Quote:
Certainly wheel torque and propulsive force are related by wheel radius, which less dragsters remains close to constant. However, the further back we go in the drive train; wheel, driveshaft, transmission, crankshaft, etc. and the more you speak about torque (unless you are concerned about the strength and stiffness requirements of these components) the more torque becomes a bit meaningless. Clearly we agree that torque at the crank (without taking into account all gearing in the drivetrain) really tells you NOTHING about vehicle performance. Thus why stop at the axle! The simplest and must fundamental concept is indeed propulsive force. Next, why worry about averaging when you can focus more simply about maximizing instantaneous propulsive force? It just adds conceptual and mathematical complexity that is not required to understand the issue to worry about averaging and/or power, the former technically requires numerical integration of a curve... No worries, we're pretty well on the same page here.
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
|
Appreciate
0
|
06-04-2013, 02:33 PM | #77 |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
I think you already are aware of this but 3450 is wet, no driver. If that weight was realized for any car, the manufacturer would report ~>3600 curb weight. As mentioned prior these simulations are absolutely including a 160 lb driver in addition to the weight shown in the dialog box input.
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
Appreciate
0
|
06-04-2013, 02:39 PM | #78 |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
I disagree. If this simulation is correct on this point, and I believe it to be almost for sure so, redline shifts will be required in gears 1-3 or 1-4 in the new car for maximum acceleration, which is identical to the existing car. If you want the maximum performance, redline will be required, simple. Of course you could avoid some of the odd feeling associated with the tapering off of torque and acceleration at high rpms by shifting a bit early. Ultimately though that is like hoping you earn less money so you can pay less taxes!
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
Appreciate
0
|
06-04-2013, 02:45 PM | #79 | |
Major General
![]() ![]() 5494
Rep 7,060
Posts |
Quote:
![]() |
|
Appreciate
0
|
06-04-2013, 04:43 PM | #80 |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
Here are the abbreviated M5 results to address the ongoing questions as to ideal shift points in that car.
Only the first three shifts (into 4th gear) are to be made at redline for maximum performance. Sorry the curve traces are so wide, for some odd reason I could not get them narrow as before which is the default. Either way one can still fairly see the curves crossing. ![]() The software automatically determines the ideal shift points based on the force curves crossing and reports them in tabular form as well. 7th gear is not shown in the table (minor bug): ![]() Also, for clarity I am not just using peak torque and hp values but curves almost exactly as supplied by BMW.
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
Appreciate
0
|
06-04-2013, 07:09 PM | #81 |
General
![]() ![]() ![]() ![]() ![]() 21156
Rep 20,745
Posts
Drives: 2021 911 turbo
Join Date: Jan 2012
Location: Montreal
|
Swamp is correct. The M5 does not need to be shifted at red line in the higher gears as clearly indicated in the graph. This is also true for the 1M. I came to the same conclusion with a similar analysis previously.
To me, this is also an indication that the gear ratios on the M5 were not optimized for best overall acceleration (maybe a compromise for MPG and/or comfort ![]() My hope is that the F8X M3/M4 DCT ratios are better optimized to take full advantage of the new engine. Last edited by CanAutM3; 06-04-2013 at 09:05 PM.. |
Appreciate
0
|
06-04-2013, 09:29 PM | #83 | |
Brigadier General
![]() 129
Rep 3,099
Posts |
Quote:
http://ecutuninggroup.com/files/2013...ning-Group.jpg if you shift before redline there, you lose acceleration... well except like 6-7 since it's a super long gear to a slightly slightly longer gear, not enough of a difference. same for any i can find on google i used to use: http://vlsicad.ucsd.edu/~sharma/Potpourri/perf_est.html VERY good tool there... but it seems to be down now? sad... had to use http://glennmessersmith.com/shiftpt.html#data but it IS about average power (multiplied out) therefore average torque man... what are you talking about? ok, we're kinda saying the same thing though - yes it's about average power, which comes from torque, but if your actual at a certain RPM geared out is lower... you'll simply be putting less to the ground in the longer gear it's not JUST about torque, it's EVERYTHING about torque, torque at the fly then multiplied through the gearbox, then the diff... if the next gear is a certain amount longer, AND the torque drop is too sharp, then yes you can shift early ED: ah graphs above, and 7 speed, i was working off 6mt- every gear up to 5th was redline and even then it was only 100something off. not sure on why you're getting 7080 in 4th and i'm not though, very strange Last edited by flinchy; 06-04-2013 at 09:49 PM.. |
|
Appreciate
0
|
06-04-2013, 09:37 PM | #84 | |
Brigadier General
![]() 129
Rep 3,099
Posts |
Quote:
1m/135i you shift at 7000 in 1-2 then after that it drops to about 6900, 6750, 6600 or something from memory.. certain people's tunes let them go to 7000 in 3rd as well, but that's a case by case basis. even with the (somewhat unrealistic) torque curve provided in the OP, with the gearing also provided (at possibly off ratios)... using a calc, it's shift to 4th at redline, then the taper i put in is a bit higher than the OP, so 7,7, 7,6 as the ratios get REALLY close together with a REALLY steep taper. pretty poor optimising of ratios, if they were a bit further apart, the whole rev range could be happily used AND it'd rev lower in top gear on the highway lol. Last edited by flinchy; 06-04-2013 at 09:48 PM.. |
|
Appreciate
0
|
06-04-2013, 10:30 PM | #85 | |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
Quote:
I did note that the only shift at redline in your set of suggested gears was 1->2.
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | |
|
Appreciate
0
|
06-04-2013, 10:36 PM | #86 |
Lieutenant General
![]() ![]() ![]() ![]() 625
Rep 10,407
Posts |
flinchy: The links you provided are entirely irrelevant. The torque curve I am using for the new M4 is nearly exactly like the FACTORY DYNO from BMW for the M5, just adjusted for a bit higher redline. The method to calculate shift points is precisely as I described earlier and this is precisely what CarTest is doing. Until you can offer some proof of your proposition on the F10 M5 gearing/shift points, with a clear description of how the calculation is being performed, you're not positively contributing to the discussion here.
Last but not least you should also do some reading on some of the (epic) debates here on the forum about power vs. torque. I used to think about vehicle performance a bit like you are. It is kind of a crutch for truly understanding the power (no pun intended) and simplicity of power (over torque).
__________________
E92 M3 | Space Gray on Fox Red | M-DCT | CF Roof | RAC RG63 Wheels | Brembo 380mm BBK | | Vorsteiner Ti Exhaust | Matte Black Grilles/Side Gills/Rear Emblem/Mirrors | | Alekshop Back up Camera | GP Thunders | BMW Aluminum Pedals | Elite Angels | | XPEL Full Front Wrap | Hardwired V1 | Interior Xenon Light Kit | Last edited by swamp2; 06-11-2013 at 12:14 AM.. |
Appreciate
0
|
06-04-2013, 11:09 PM | #87 | |
Lieutenant Colonel
![]() 290
Rep 1,577
Posts |
Quote:
![]() Dude don't get your panties all in a bunch, i just wanted to know where you got your data, I see now, from "the first couple of pages" from google comment that you've got about as much "proof" as what i offered, at least I had the decency to link the damn sites. ![]() Oh and thanks for saying a might be naive, you're a real class act. ![]() |
|
Appreciate
0
|
06-05-2013, 12:29 AM | #88 | |
First Lieutenant
![]() ![]() 125
Rep 353
Posts |
Quote:
![]() |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|