OLED Tail Lights for F80 M3

[jd__m4]

Originally Posted by F80_Greg

Sorry boys, just jokes 😂

Lmao stealing this

[e92motorsports]

Have V1s installed on a 2015. Reverse lights flickering, any help is GREATLY appreciated !

[F80_Greg]

Originally Posted by e92motorsports

Have V1s installed on a 2015. Reverse lights flickering, any help is GREATLY appreciated !

Refer to page 25 i believe it's on. Most likely your resistor box is not wired correct

[SeatownF90]

I put my car in reverse, put on ebrake, open the door and walked to the back to see how it looks. "oh shit my reverse light is broken!" Then I realized the car goes to neutral when you open the door in reverse /smh

[F80_Greg]

After receiving over 20 pm's, just dropping the link here lol. Anyone can find it by searching. Just message them and work out a deal. All Alibaba sellers are willing to negotiate. Ask for EMS shipping if you want it in 1-2 weeks


https://m.alibaba.com/product/160017...00000%22%7D%7D

[bryhsiao]

Originally Posted by SeatownF80

I did. It sits flushed with LCI drip rails, though difference is pretty minor. $70 for piece of mind.

LCI drip rails? can you tell me where you bought to prevent water coming in?
also where you bought from? a link pls? how long do you have to wait? fitment?

[TRYM3]

Originally Posted by TrauCon

Check youtube for "BIMMERCODE: CODING DRL REAR LAMPS TO STAY ON"
around 2:00 min mark.

thank you!

[11LMBiSTT]

Anyone in So Cal want to lend a hand/supervise me with my install, that's already done it before? Food or beer will be provided.

[TRYM3]

Originally Posted by diesel733

Has anyone wash or drive their cars in the rain yet? Trying to see if any issues to report in terms of moisture or condensation in the lens when ? I'm very OCD when it comes to that

I washed my car here in central PA, washed it outside in about 27 degrees Fahrenheit then pulled it in a warm garage to dry it off and zero condensation. I dont anticipate them having any either in the future.

[SeatownF90]

Originally Posted by bryhsiao

LCI drip rails? can you tell me where you bought to prevent water coming in?
also where you bought from? a link pls? how long do you have to wait? fitment?

credit to E92inSG for the suggestion and part number.

Part numbers: 51497453333 & 51497453334

from getbmwparts.com

Pressure washed mine and trunk was dry and lamps had no condensation

[weytie]

Originally Posted by F80_Greg

Sorry boys, just jokes 😂

Until the F82 ones are realeased we maybe get lost of that Christmas startup sequence

[F80_Greg]

Originally Posted by weytie

Until the F82 ones are realeased we maybe get lost of that Christmas startup sequence

Lol, rumor down in Chinatown Is that they are working on a f32 / f82 development in the next few coming weeks

[TRYM3]

Any one have any coding knowledge? I coded in drl for the tail lights and it shows active but they do not stay on as they should.... thanks for any advice

[hC1001]

If anyone is able to modify the turn signals to be non sequential, id be interested. I didnt open up the lights but opening up the plugs revealed PCB board with a lot of components soldered onto it. I believe the sequential turning lights are "hardwired" and wont be easily modified to blink at the same time.

One thought is to delay the turn signal on the inner light to match the outer light so it turns on at the same time. I also noticed within each outer and inner light, its sequential as well. I can live with that and think it wont be too noticeable if they blink at the same time.

Im not an electrician but i hope someone who is can chime in. From what i gather, you can connect a resistor and capacitor in series on the inner turn signal to delay when it blinks. I attached a wire diagram and i think it just needs to be added to the blue and green wires(inner turn signal light). I would modify the aftermarket tail light wire harness and not the chassis harness.

Thanks for any help.

[SikhF80]

Originally Posted by TRYM3

This is just 2 quick things I wanted to point help while installing bayoptiks aka v2s
They might be no brainers to most of you on here but just a few things I had questions on and it might help a few of you out while installing. Other then that my v2 install was a breeze it took me about 30 minutes and fitment is damn near perfect.

What are the extra wires for. Bayoptics has some small wires there not sure for what

[BzsBimmer]

Originally Posted by SikhF80

What are the extra wires for. Bayoptics has some small wires there not sure for what

Would help to explain number of wires, more descriptive information.
Assuming it’s the two small wires? Those connect the trunk lights on some models. Does the video not show them?

[SikhF80]

Originally Posted by BzsBimmer

Would help to explain number of wires, more descriptive information.
Assuming it’s the two small wires? Those connect the trunk lights on some models. Does the video not show them?

First video at 1:18. The small wire. I have a 2018 model and oem did not have those. I saw another youtube video where the guy didnt connect those two small wires. Do we know what its for?

[BzsBimmer]

He mentions it in the video. Pre LCI. We talk about it a lot on this thread but most people don’t have the patience to read back.
You’re 2018 so probably not needed based on what others have said. I’m preLCI so I needed them. They connect to the inner lights like I stated.

[hC1001]

Originally Posted by SikhF80

First video at 1:18. The small wire. I have a 2018 model and oem did not have those. I saw another youtube video where the guy didnt connect those two small wires. Do we know what its for?

The 2 pin yellow and red wire is from the aftermarket outer tail lights. Its not original to the car.

They connect to the inner aftermarket tail lights so the brake lights turn on in the inner lights. You have to route them through the hole between the two mounting studs of the outer tail light.

[SikhF80]

Originally Posted by hC1001

The 2 pin yellow and red wire is from the aftermarket outer tail lights. Its not original to the car.

They connect to the inner aftermarket tail lights so the brake lights turn on in the inner lights. You have to route them through the hole between the two mounting studs of the outer tail light.

I didnt connect them but the brake lights still work

[hC1001]

Originally Posted by SikhF80

I didnt connect them but the brake lights still work

Your inner brake lights arent working.

If you want to have the inner brake lights also turn on like the outers, you need to connect that long wire from the outer lights to the inners.

[SikhF80]

Originally Posted by hC1001

Your inner brake lights arent working.

If you want to have the inner brake lights also turn on like the outers, you need to connect that long wire from the outer lights to the inners.

Ahh got it thanks. Will do that some other time lol